1) metal/ceramic particles
金属/陶瓷颗粒
2) ceramic particles reinforced composite
金属基陶瓷颗粒增强
3) porcelain granule
陶瓷颗粒
1.
A process and formulation suitable for electroless nickel plating on porcelain granules is developed.
研制了一种适合陶瓷颗粒表面化学镀镍的酸性化学镀镍工艺和配方,重点分析了镀液成分、温度、pH值、施镀时间等工艺参数对镀层外观质量的影响。
2.
An alkaline solution suitable for electroless nickel plating on porcelain granule was developed, and an equipment suitable for processing granule material was also designed.
研制了一种适用于对陶瓷颗粒进行化学镀镍的碱性化学镀镍配方及工艺,并设计出适用于对颗粒材料进行化学镀的试验设备。
4) ceramic particle
陶瓷颗粒
1.
The developing situation of metal matrix composite reinforced by ceramic particle is introduced.
介绍了陶瓷颗粒增强金属基复合材料的进展状况,重点介绍了几种常用的制备方法,提出了一种新的制备工艺—块体分散法。
2.
In this paper, the fundamental principles and basic techniques about copper coating on the surface of TiB_2 and Ti_3SiC_2 ceramic particles by electroless plating were discussed.
用粉末冶金的方法制备了石墨-铜基复合材料、导电陶瓷颗粒/石墨-铜基复合材料和镀铜导电陶瓷颗粒/石墨-铜基复合材料。
3.
A method to prepare transmission electron microscopy(TEM) thin foil for analysis of ceramic particle was introduced.
本文介绍了一种对陶瓷颗粒进行透射电镜分析的样品制备方法。
5) ceramic particles
陶瓷颗粒
1.
Numerical analysis of moving and heating of ceramic particles in plasma jet spray tooling;
等离子体射流中陶瓷颗粒的运动与加热
2.
Four kinds of WC, ZrO_2, Cr_2O_3 and Al_2O_3 ceramic particles/nickel alloy composite coatings were prepared with the plasma spraying method.
采用等离子喷涂工艺,制备了WC、ZrO2、Cr2O3和Al2O3陶瓷颗粒/镍合金复合涂层。
3.
Four kinds of ceramic particles of WC,ZrO2,Cr2O3 and Al2O3 were used as an reinforced phase and the nickel alloy powder as a matrix, the erosive wear properties of four types of composite coatings fabricated with plasma spraying were experimentally studied with the wear test equipment.
以WC,ZrO2,Cr2O3和Al2O3陶瓷颗粒为增强相,镍合金粉末为基体,运用等离子喷涂技术制备四种陶瓷/镍合金复合涂层。
6) Ceramic wear debris
陶瓷颗粒
1.
Object To study the effect of adherent endotoxin of alumina ceramic wear debris on secretion of TNF-α cytokines by human monocytes in different time and concentration, searching after the role of endtoxin in artifical joint biological loosening.
目的 通过对粘附不同浓度内毒素的氧化铝陶瓷颗粒对人单核细胞分泌TNF-α不同时间的表达影响，探讨内毒素在人工关节生物性松动的作用。
补充资料：活性金属法陶瓷-金属封接
分子式：
CAS号：
性质：将活性金属粉(如钛、锆、铪等)与，有机溶剂调合成膏状涂敷在要封接的陶瓷表面上。在涂有活性金属粉的陶瓷和金属零件之间放置能在较低温度下形成合金的金属焊料(如银、铜、镍、银-铜等)，在真空或惰性气氛中加热而使陶瓷-金属气密性封接的一种方法。活性金属对各种氧化物和硅酸盐均有较强的亲和力，可实现气密封接。以钛；银-铜法用得最为广泛。活性封接法的优点是工序少、周期短、瓷件不会变形，成品率高。但结构上对针封、套封较困难，也很难连续生产。
CAS号：
性质：将活性金属粉(如钛、锆、铪等)与，有机溶剂调合成膏状涂敷在要封接的陶瓷表面上。在涂有活性金属粉的陶瓷和金属零件之间放置能在较低温度下形成合金的金属焊料(如银、铜、镍、银-铜等)，在真空或惰性气氛中加热而使陶瓷-金属气密性封接的一种方法。活性金属对各种氧化物和硅酸盐均有较强的亲和力，可实现气密封接。以钛；银-铜法用得最为广泛。活性封接法的优点是工序少、周期短、瓷件不会变形，成品率高。但结构上对针封、套封较困难，也很难连续生产。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条