1) compound artificial synovia
复合人工滑液
1.
The compound artificial synovia was prepared according to the table of orthogonal test design, which three factors-Hyaluronic Acid, γ- globulin and Lα-DPPC and five levels were considered.
利用正交实验设计配制由透明质酸HA、Lα-DPPC磷脂和y-球蛋白3种成分构成的复合人工滑液,在PVA-H/PVA-H,PVA-H/316L S S两类人工关节摩擦副上,利用自制振子式摩擦仪测定其摩擦学参数,初步确定出复合人工滑液中3种成分的适宜配比。
3) artificial synovial fluid
人工滑液
1.
Supporting the study of artificial articuar cartilage materials, the research and development of an artificial synovial fluid of Hyaluronic acid (HA) was carried out.
配合人工软骨材料的研究,探讨透明质酸(HA)作为摩擦副的人工滑液时的润滑性能。
4) artificial synovia
人工滑液
1.
A compound artificial synovia was prepared by adding Lα-dipalmitoyl phosphatidylcholine(L α-DPPC) riposomes and γ-globulin to a saline of sodium hyaluronate (HA),by which two kind of tribology slider pairs-PVA-PVA-H/VA-H and PVA-H/316L S.
在透明质酸为主要成分的人工关节润滑剂中添加Lα-DPPC磷脂和γ-球蛋白,配制成复合人工滑液,在PVA-H/PVA-H,PVA-H/316 L S。
2.
In order to find the potential factors resulting in significant improvements in the lubricating be- havior of a compound artificial synovia, which was prepared by ourselves with hyaluronic acid mainly and some proteins and phospholipids, the technology of Atomic Force Microscope (AFM) was used to observe the appearance of adsorbed film on material surface formed by the compound artificial synovia.
用原子力显微技术(AFM)观测复合人工滑液在材料表面形成的吸附膜的表面形貌图 像,吸附膜上清晰地显示有大量的椭球形分子。
3.
The rheological characteristics of an artificial synovia mainly consisting of hyaluronic acid prepared by editors was discussed.
研究以透明质酸为主要成分的人工滑液的流变性质,分析添加γ-球蛋白和La-DPPC 磷脂对人工滑液流变性能和润滑性能的影响,并结合滑液粘弹性质与摩擦副表面理化性质对 润滑模式进行了探讨。
5) composite cooling liquid
复合工作液
1.
One kind of commercial WEDM-HS was successfully designed and launched on market through improving the structure of machine,innovating the control system and using composite cooling liquid which has powerful washing ability.
分析了高速走丝电火花线切割机床多次切割的条件及进行稳定多次切割需采取的措施,通过对机床机械结构及控制系统功能的改进与完善,采用洗涤性能良好的复合工作液,成功研制出具有稳定多次切割功能的商品化机床。
2.
The experiment shows that the machining indexes of HSWEDM improve remarkably after using the composite cooling liquid with better washing ability to improve cooling situation at gap.
从极间放电机理的角度分析了阻碍高速走丝电火花线切割加工(HSWEDM)工艺指标提高以及产生表面黑白交叉条纹的根本原因是工作介质的洗涤性问题,试验证明HSWEDM在使用洗涤性良好的复合工作液后,由于极间冷却状态的改善而使切割工艺指标大幅度提高,切割速度已超过200mm2/min。
3.
Interelectrode discharge mechanism and cutting technique rule of aluminum alloy cut by HSWEDM were studied by adopting the high efficiency cutting technology of aluminum alloy based on(using) composite cooling liquid as discharge dielectric to obtain even cooling gap situation.
采用复合工作液作为放电介质以获得极间均匀冷却的铝合金高效电火花线切割技术,研究了铝合金电火花线切割的极间放电机制及切割工艺。
6) complex dielectric fluid
复合工作液
1.
Morphology feature and processing rule of cut mono-crystal silicon(mc-Si) based on complex dielectric fluid used in wire cut electric discharge machining with high traveling speed(WEDM-HS)is researched.
研究了基于复合工作液的高速走丝电火花线切割(W EDM-HS)对单晶硅切割的形貌特征及工艺规律。
2.
A solar wafer slicing method was studied,which was based on complex dielectric fluid and efficiency electric discharge machining(EDM) and electric chemical machining(ECM) technique.
提出了一种基于复合工作液的、以电火花电解复合加工技术对太阳能硅片进行切割的工艺方法。
3.
A new technology cutting with synchronizing texturing on solar wafer is researched,which is based on complex dielectric fluid and using compound electric discharge machining(EDM) and electrochemical machining(ECM) technique.
提出了一种基于复合工作液的以电火花电解复合加工技术对太阳能级硅进行切割及制绒一体化的新方法。
补充资料:滑液
1.光润。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条