说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 泵阀
1)  pump valve
泵阀
1.
Reasons for higher degrading rate of Model 3DJ polymer injection pump and modification of pump valve;
3DJ型注聚泵降解率偏高原因分析及泵阀改进
2.
A novel method for fault diagnosis in a drilling pump valve based on an improved Hilbert-Huang transform;
基于改进希尔伯特-黄的泵阀故障诊断新方法
3.
Feature Extraction in Fault Diagnosis of Pump Valve and GSM-Based Remote Failure Alarm Equipment;
钻井泵阀的故障特征提取与基于GSM的远程故障报警仪
2)  valve [英][vælv]  [美][vælv]
泵阀
1.
Method for calculating pressure drop over valve of sucker rod pump;
抽油泵阀开启压差的计算方法
2.
LVDT Transducer s Application to Kinematics Test of the Valve of Mud Pump;
LVDT 传感器在钻井泵阀体运动学测试中的应用
3.
In the paper, the influence of the Westphal's pheonmenon of the movement of the pump valve and the compressibility of the liquid on the continuous flow condition of liquid in the cylinderbeing not only comprehensively considered, but also the dynamic property of the pump valve being reserched, a new accurate dynamic model used to describing movement of the pump valve is set up.
综合考虑了液体可压缩性、泵阀运动的魏氏效应对泵筒内液体连续流条件的影响,并考虑了泵阀运动的动力特性,建立了新的泵阀精确运动微分方程,该数学模型不存在奇点问题。
3)  Drilling pump valve
泵阀
1.
The design of drilling pump valve directly influences its working performance and service life.
泵阀是钻井工作过程的直接组成件,也是钻井泵中最重要的易损件之一。
4)  pump valve-ball
抽油泵泵阀
1.
It is the key study how to make sure the pressure distribution of liquid in the pump barrel and to study the pump valve-ball's movement to improve the systematic efficiency.
对有杆抽油泵泵阀运动规律的研究和确定抽油泵泵阀筒内液体压力的分布是提高抽油机井系统效率研究的关键性课题。
5)  valves of the fracturing pump
压裂泵泵阀
6)  reciprocating-pump valve
往复泵泵阀
1.
Based on systematical analysis and study about the existed reciprocating-pump valve design theory and virtual manufacturing technology,study the high-pressure reciprocating-pump valve virtual design technique according to practical experience in design and improvement about reciprocating-pump of manufacturers.
在对往复泵泵阀设计理论和虚拟制造技术进行系统分析和研究的基础上,结合产品设计和改造的实际经验,对往复泵泵阀的虚拟设计技术进行了研究。
补充资料:泵阀等供水设备及主要配件基础知识

A、水泵基础知识知识


    常用水泵型号代号
    LG-----高层建筑给水泵
    DL------多级立式清水泵
    BX-------消防固定专用水泵
    ISG------单级立式管道泵
    IS -------单级卧式清水泵
    DA1-------多级卧式清水泵
    QJ-------潜水电泵


    泵型号意义:如40LG12-15;40-进出口直径(mm);LG-高层建筑给水泵(高速);12-流量(m3/h);15-单级扬程(M)。
    200QJ20-108/8。200---表示机座号200;QJ---潜水电泵;20—流量20m3/h;108---扬程108M;8---级数8级。


    水泵的基本构成:电机、联轴器、泵头(体)及机座(卧式)。[见图]


    水泵的主要参数有:流量, 用Q表示,单位是M3/H ,L/S。扬程,用H表示,单位是M。


    对清水泵,必需汽蚀余量(M)参数非常重要,特别是用于吸上式供水设备时。


    对潜水泵,额定电流参数(A)非常重要,特别是用于变频供水设备时。


    电机的主要参数:电机功率(KW),转速(r/min),额定电压(V),额定电流(A)。


    联轴器    泵头(体_)    卧式机座


    B、压力容器基本知识


    1、压力:压力是垂直作用于物体单位面积上的力。确切名称是压力强度,简称压强,习惯上叫做压力[kgf/cm2]。压力的单位一般用大气压,在工程单位中用公斤/厘米表示,也可以用水柱或水银柱表示,国际统一单位是牛顿[N/mm2]、帕或兆帕[MN/m2 、 Mpa]。1工程大气压[kgf/cm2]=0.098牛顿[N/mm2]=0.098帕[MN/m2]=0.098兆帕[Mpa]=10米水柱的压强。


    2、容器:容器是由曲面构成用于盛装物料的空间构件。容器大体是由:筒体、封头(端盖)、发兰、支座、接管、人孔等组成。


    3、补气式、囊式供水设备罐体的总容积、可调水容积计算及水泵启动次数:


    VZ=Vx/1-αb  Vs=βCqb/4nmax  Vo=Vs(β-1)/(1-αb)


    筒体重量计算:W=7.85Dnπhδ/106[Kg]。


    封头的下料参考尺寸Ø =1.2Dn+2S+2倍直边高度(25、40、50)mm


说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条