1) hollow ingot
空心铸锭
1.
Mandrel forcing and deformation during upsetting when tube is extruded by hollow ingot are researched in the article The result shows that mandrel bears bending stress and causes bending deformation, thus causes eccentricity in front end of the extruded tube,the life of the mandrel can be reduce
研究了用空心铸锭挤压管材时在镦粗过程中穿孔针的受力及变形情况。
2) hollow
空心
1.
Bone Transplantation for Fracture of Lumbar and Thoracic Vertebrae Through Hollow Bone-planting Appliance;
经椎弓根空心椎体植骨器的设计与临床应用
2.
Construction technology of hollow and high pier of railway bridge;
铁路桥梁空心高墩施工技术
3.
The preparation and application of hollow core-shell structured nanomaterials were introduced in this article.
本文对空心核壳结构纳米粒子的制备研究及应用进行了综述。
3) hollow square pile
空心方桩
1.
The article introduces the main characteristics and application prospect of prestresses reinforced concrete hollow square pile.
文章介绍预应力钢筋混凝土空心方桩的主要特点及应用前
2.
Prefabricate hollow square pile is a kind of new pile,of which performance is between the solid square pile and prestressed pipe pile.
预制空心方桩兼备预制桩和预应力管桩的一些特性。
4) fly ash cenospheres
空心微珠
1.
Electroless plating Co-P alloy on the surface of fly ash cenospheres;
空心微珠表面化学沉积Co-P合金研究
2.
Nanocomposite microwave absorbing coatings were prepared by using prepared Ni-Co-P/CNT and Ni-Co-P/fly ash cenospheres composite powders as absorbers,choosing epoxy resin as film forming resin and adding some proper solvent,curing agent and auxiliary agents.
以Ni-Co-P/CNT复合粉体和Ni-Co-P/空心微珠复合粉体作为吸收剂,选用高分子聚合物环氧树脂作为成膜树脂,同时加入适当的溶剂、固化剂和助剂制备出纳米复合微波吸收涂料,并将涂料涂刷于塑料薄板上制备出涂层样品。
5) hollow microsphere
空心微球
1.
NiS2 hollow microspheres were prepared by hydrothermal reaction between NiCl2·6H2O and Na2S2O3·5H2O at the low temperature of 150°C.
5H2O为原料,在150℃较低温度的水热条件下制备了NiS2空心微球,用XRD和SEM对产物进行了表征,NiS2粉体的X射线衍射的衍射峰均与标准衍射图一致(JCPDS:653 325,立方晶系,a=0。
2.
Subsequently, the similar microstructured NiO hollow microspheres were obtained by calcining the above precursor at 400 ℃ for 2 h.
报道一种非常简单的制备NiO和Ni(OH)2空心微球的无模板水热法,即通过NiCl2与氨水在140℃水热反应12h,制备了Ni(OH)2纳米片自组装的空心微球,经400℃热处理2h得到了NiO空心微球。
3.
NiS hollow microspheres were synthesized by the reaction of nickel acetate and thioacetamide inethanol at 150 ℃.
以醋酸镍和硫代乙酰胺为原料,乙醇为溶剂,在150℃的溶剂热条件下制备了硫化镍空心微球,并用XRD,TEM,SAED和SEM对产物进行了表征。
6) hollow ingot
空心钢锭
1.
Effect of Mould Structure on Hollow Ingot Solidification;
空心钢锭锭型结构对空心钢锭凝固过程的影响
2.
Study on the Heat Transfer Boundary Conditions of Core in Hollow Ingot;
空心钢锭芯部换热条件的确定
参考词条
补充资料：生铁模铸锭
生铁模铸锭
iron mould casting
shengtlemu Zhudlng生铁模铸锭(iron mould easting)将熔体注入生铁模型铸造锐坯的工艺方法。生铁模铸锭是有色金属合金铸锭生产最常用、最简单的一种铸锭方式。由于方法简单、灵活以及投资少等特点，在中、小型企业中广泛应用。生铁模和在生铁模基础上发展起来的水冷生铁模铸锭，按浇注方式划分有水平锭模铸锭、垂直锭模铸锭和倾动锭模铸锭;按锭模结构划分，在垂直锭模铸锭中还分整体式锭模铸锭和对开式锭模铸锭。 水平锭模铸锭生产像铅、锡类的低熔点金属合金以及对铸锭表面和内部组织无严格要求、不直接用于塑性加工的铸坯，如中间合金铸块、各种废料和回炉重熔的铸块等。 垂直锭模铸锭用于铜及铜合金锭坯生产。垂直锭模分整体式和对开式两种口整体式垂直锭模用于圆柱形断面铸坯生产，为了脱模方便，模内壁加工成一定锥度。这种锭模铸锭几何尺寸稳定、铸翅少，但不适于径高比小和凝固收缩率小的铸坯生产。对开式垂直锭模与整体式垂直锭模相比，更有利于模子内壁的清理和润滑，也易于脱模，但这种锭模铸锭易产生铸翅和变形。不论整体式还是对开式的垂直锭模都可以在模壁外侧安装水套做成水冷生铁模。 倾动式锭模铸锭常用于铝及铝合金板坯生产。浇注过程中锭模能围绕模子重心的水平轴，平稳地倾少 倾动模铸锭浇注过程示意图 1一浇包;2一金属液体流;3一金属模;4一模座动一定的角度，使液流沿锭模侧边稳定地流入模底(见图)。液流的表面氧化膜受到保护，液流在模内也不产生激烈的翻腾和搅动。 倾动模铸锭能有效地减少氧化损失和防止产生因液体金属的机械运动而带入的金属氧化夹渣和过量的有害气体所造成的铸锭缺陷。 (郎振旗)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。