1) high-quatity of sintercast
烧结机高产
2) Sintering
['sintəriŋ]
烧结生产
1.
This paper mainly analyzes the impacts of the fluctuation of return fines quality and quantity on sintering,putting forth countermeasures of controlling best return fines quantity through reducing water and carbon fluctuations and increasing surface-layer sintered ore strength.
主要分析了返矿质量和数量的波动对烧结生产的影响,提出了通过减少水、碳波动,提高表层烧结矿强度等来控制最佳返矿量的对策。
3) sinter production
烧结生产
1.
This paper summarizes the feasibility and results of sinter production with washed coal as fuel instead of raw coal,under the material and fuel conditions at Anyang Iron and Steel CorpIt has been proved by practices that,the content of SiO2 is reduced and the TFe of sinter is increased by this and as the consequence the technical and economic indexes of blast furnace are improve
本文论述了在安钢原、燃料条件下用洗精煤替代原煤作燃料的烧结生产可行性研究及效果。
2.
The dose of all kinds of materials and control of sinter parameters are key to sinter production.
本钢烧结生产过程由原料、配料、烧结和成品运输4个部分组成,各个部分的开关量、模拟量和控制回路多,且相互影响。
4) sintering production
烧结生产
1.
In order to improve the situation that the sintering production capacity cannot follow the increase of that in iron-making, measures are taken such as increasing pellet ore and lump ore, raising sintered ore basicity, improving properties of sintered ore and promoting the optimizing of BF burden structure.
针对随着炼铁产能的提高烧结生产能力不足的现状,通过采取增加球团矿和块矿用量、提高烧结矿碱度、改善烧结矿性能等措施,促进高炉炉料结构进一步优化,为高炉提供优质原料,满足炼铁生产。
2.
The indurical exprement and production shows that it is workable to use directly making-steel sludge in sintering production at NO2.
马钢二烧配用炼钢湿基污泥的试验和生产表明，在烧结生产中，直接利用炼钢湿基污泥是可行的，利于提高料层厚度，实现厚料层烧结，提高烧结矿产量，具有可观的经济和社会效益。
3.
The development of SHAOGANG sintering production was summerized,and the developing direction in future was forecaste
总结了韶钢烧结生产的发展过程 ,提出了今后发展的方
6) sintering process
烧结生产
1.
On the condition of guaranteeing the quality of sinter and stability of productive process, the sintering process of adding ferruginous waste such as steel-making slag, iron oxide scale and dust separately is analyzed.
实践证明 ,在烧结生产中配加钢铁废料 ,可以稳定生产 ,保证烧结矿品位合格 ,降低烧结矿成本 ,降低能源 ,合理利用资
2.
In order to decrease the cease-operation rate and stabilize the processing, an expert system for diagnosing abnormal status of sintering process has been designed and developed, whose aim is to diagnose the whole sinter.
烧结生产是一个工艺流程长、影响因素多、机理复杂的动态系统。
3.
A rule-based abnormity diagnosis expert system for sintering process has been designed and developed by means of Visual Studio.
Net和Matlab混编的方式,结合ADO数据库技术,将整个烧结生产工艺过程作为诊断对象,设计开发出基于规则的烧结生产异常诊断专家系统。
补充资料：带式烧结机烧结
带式烧结机烧结
sintering by sinter strand
一种应用最广的铁矿石烧结方法。带式烧结机是钢铁工业的主要烧结设备，它的产量占世界烧结矿的”%。现代带式烧结机的烧结室的断面示于图1。烧结机是由铺设在钢结构上的封闭轨道和在轨道上连续运动的一系列烧结台车组成。首先将从烧结矿中分出的铺底料(10~Zomm)加在台车上，以保护台车算条和减少废气含灰量。然后再将烧结混合料经布料机加到台车上，并保持规定的高度。随之进行抽风点火烧结，随台车前进，烧结过程由料层表面不断向下进行。至机尾，烧结完成，台车翻转将烧结饼倾卸。空台车沿下部轨道运行至烧结机头部，再加料进行点火烧结，如此循环不断。烧结饼经破碎和筛出热返矿后，送冷却机冷却。从料层中抽出的废气经台车下的风箱至集气总管和除尘装置，由抽风机排向烟囱。dalshi shaojieji shaojie带式烧结机烧结(sintering by sinter strand)}馨爵鬓 森币乒、，一，，，，.、一，r，_， 图1现代抽风带式烧结机烧结室断面图 带式烧结机由烧结台车、密封装置、钢结构框架和3.om、3.sm、4.om及5.om几种。由于台车处于高温传动装置组成。台车是放置烧结料和进行抽风烧结的下工作，因之不仅要求材质能耐高温、而且要求结构合重要部件。它是由铸钢车体、侧板、算条和滚轮组成(见理减少高温变形的影响。在台车和风箱滑道之间有密图2)。按烧结机大小、台车宽度有1.sm、2.om、2.sm、封装置(水管式密封或弹簧式密封)，对减少漏风和节 省电耗有很重要的作用。在机头和机尾的风箱隔板与 ‘卜~一一-一-2500—--，司 创盯一一一下台车之间用重锤连杆式密封。为保证台车在受热膨胀 .对胭奎至斋荞至幕筹拜三三三三三尸气润后仍能平稳运转，在机尾卸矿端设置专门的摆动机架 书阳~一一一即一一邵一二一一一.一-期d{丹一去或可水平移动的尾部星轮。烧结台车借助于机头部分 !毛一一一一，。。州泞的传动装置向前运动，传动装置是由电动机、减速机和 卜卜一一一一-—3216—一一一一月’传动大齿轮所组成。(见彩图插页第2、3页) (杨兆祥蔡法率)纂戳磷~ 图2烧结台车
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条