1) Short circuit modification
短路改造
2) pipeline transformation
管路改造
3) old road rebuilding
旧路改造
1.
A brief talk on the alignment design of the old road rebuilding;
浅谈旧路改造工程线形设计
2.
Application of subgrade treated by dynamic compaction in old road rebuilding;
路基强夯在旧路改造中的应用
3.
It is a effective old road rebuilding scheme that laying asphalt concrete layer on the old cement concrete pavement to improve its intension to meet the demand of traffic.
本文介绍了玻纤格栅在旧路改造中防止反射裂缝的应用。
4) road rebuilding
道路改造
1.
The article probes into the mathematical model suitable for the alignment fitting of the longitudinal sectional design of the road rebuilding, and puts forward the method using the computers the carry out the longitudinal sectional alignment design of the road rebuilding.
该文对适用于道路改造纵断面设计线形拟合的数学模型进行了探讨,提出了利用计算机进行道路改造纵断面线形设计的方法。
2.
According to the road traffic characteristics of the impact scope of Jiefangbei CBD ,the paper used the idea of traffic impact analysis to bright up road rebuilding or improvement project plans and traffic organization plans, evaluated the effects of all the plans, recommended the proper definition and scale of CBD development.
利用交通影响分析的理念,针对重庆解放碑片区CBD的重要影响范围的道路交通特征,提出道路改造或改善方案和交通组织方案,评价各方案的交通效果,推荐CBD开发的定位与适度规模。
5) transformation of old road
旧路改造
1.
This paper discusses main problems involved in the transformation of old road and provides that it is better to widen inferior road in one side and widen super road on both sides.
论述了旧路改造中涉及到的主要问题,并提出低等级旧路宜单侧加宽,高等级公路采用双侧加宽更加有利,路面的施工应在充分调查了解旧路面现状的基础上进行,施工中可以在接缝土处加土工织物来减少裂缝。
6) old highway reconstruction
旧路改造
1.
Design optimization and project management for old highway reconstruction;
旧路改造项目设计优化与项目管理
2.
Technology requirements for strengthening scheme in the item management of old highway reconstruction;
旧路改造项目管理中补强方案的工艺要求
补充资料:单相短路电流
分子式:
CAS号:
性质:一相导体与保护导体发生短路时流经相-零回路的电流。单相短路电流是评价和设计保护接零系统设计的基本要素。保护接零系统的单相短路电流不应小于低压断路器瞬时动作或短延时动作过电流脱扣器的整定电流的1.5倍;不应小于低压熔断器熔体额定电流的4倍。
CAS号:
性质:一相导体与保护导体发生短路时流经相-零回路的电流。单相短路电流是评价和设计保护接零系统设计的基本要素。保护接零系统的单相短路电流不应小于低压断路器瞬时动作或短延时动作过电流脱扣器的整定电流的1.5倍;不应小于低压熔断器熔体额定电流的4倍。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条