1) refrigerating extent
冷却度
1.
Given the post-throttling pressure p 2,the refrigerating extent ΔT H is larger when the initial temperature is lower and the pressure is higher before throttling.
高压至低、中压空间的液氨等焓节流过程中 ,液氨的微分节流效应 ,μH=( T/ p) H>0 ,为制冷效应 ,积分节流效应的ΔTH 数值与节流前后的状态 (T、p)有关 ,当节流后压强p2 一定 ,节流前压强p1愈高 ,温度T1愈低时 ,冷却度ΔTH 就愈大 。
2) cooling rate
冷却率;冷却速度
3) cooling velocity
冷却速度
1.
Influence of cooling velocity after coiling on the structure of high strength steel;
卷取后冷却速度对高强度热轧带钢组织的影响
2.
The results show that,when cooling velocity increases,the beginning temperature and the finishing temperature of phase transformation are both decrease,the grain is obviously refined.
结果表明:随着冷却速度的增大,相变开始温度和结束温度均降低,晶粒明显被细化。
3.
The effect of two cooling velocity on strain-aging sensibility of 16MnR hot rolled steel plate has been studied.
研究了2种冷却速度对16MnR热轧钢板应变时效敏感性的影响。
4) Cooling Rate
冷却速度
1.
Effect of Cooling Rate on Structure Evolution of Hot Deformed Ferrite-Bainite Micro Alloying Steel;
热变形后冷却速度对铁素体-贝氏体微合金钢组织演变的影响
2.
Eeffects of cooling rate on solidification structures of Al-Si-Cu sputtering targets;
冷却速度对Al-Si-Cu溅射靶材凝固组织的影响
3.
Effects of Cooling Rate on the Microstructure and Properties of Cu-Cr Alloy;
冷却速度对Cu-Cr合金组织和性能的影响
5) cooling speed
冷却速度
1.
In this paper,impact on phase transformation speed and formation produced by different cooling speed between 10k/min and 200k/min in the cooling process of steel T91 has been investigated.
本文研究了T91钢冷却过程中,不同冷却速度(10k/min(200k/min)对相变速度和产物的影响。
2.
The test shows that the cooling speed affects the first arm-spacing and the second arm-spacing, and concluded that they are decreased, the fracture fractographies are improved, and the mechanical properties, especially the toughness, is obviously increased while the cooling speed increases.
试验表明,冷却速度增大,使奥氏体的一次二次枝晶间距缩小,断口形貌改善;并且可使材质的综合力学性能,特别是韧性明显提高。
3.
To research the effect of different cooling speed on the microstructure and property of 9 mm high carbon steel wire rod by means of cooling control process and the experiments of microstructure and property and the simulated analysis.
通过控冷工艺、组织性能实验和模拟分析 ,研究了不同冷却速度对 9mm高碳钢线材组织性能的影响。
6) cooling strength
冷却强度
1.
The product properties such as tensile strength and electric conductivity effected by cooling strength and deformation were studied.
选择AZ31镁合金为原材料,在400℃下挤压散热片型材,就冷却强度及变形程度对制品的性能(抗拉强度和导电率)及组织结构的影响进行研究。
2.
Compounds in 7A52 alloy may not influence the processing property of product by means of three process parameters,such as,controlling the main element Mn in 7A52 alloy,and by aid of special moulding system and reasonably controlling cooling strength.
通过对7A52合金中的主要元素Mn等进行控制,辅以专门的供流系统,合理控制冷却强度等三大工艺参数,可以使7A52合金中的化合物不影响制品的加工性能,对提高制品的成材率有明显效果。
3.
Because taking some measures,such as selecting hot air valve with reasonable structure,improving cooling system of hot air valve and increasing cooling strength of hot air valve,etc,the service life of hot air valve is increased greatly in the practical process of vapourizing cooling of hot air valve in NO.
莱钢第二炼铁厂在热风阀汽化冷却实践中，通过采取选用结构合理的热风阀，改进冷却系统，提高冷却强度等措施，使热风阀寿命大幅度提高。
补充资料：安侬痛 ,阿那度尔,安那度尔,甲替啶
药物名称：安那度尔
英文名：Alphaprodine
别名： α-普洛丁;阿法罗定;安那度;安侬痛 ,阿那度尔,安那度尔,甲替啶
外文名：Alphaprodine ,α-Prodine, Nisentil, Prisilidene
适应症：
用于需短时止痛(镇痛起效比吗啡迅速,皮下注射5min即见效)，如小手术时以及手术后的止痛，又可与阿托品合用于胃肠道、泌尿道等平滑肌痉挛性疼痛的止痛。
用量用法：
皮下注射：１次１０～２０ｍｇ，１日２０～４０ｍｇ。 静注：１次２０ｍｇ。 极量：１次３０ｍｇ，１日６０ｍｇ。
注意事项：
1.亦有成瘾性，不宜久用。 2.有眩晕、无力、多汗等不良反应。 3.分娩时慎用，可能会引起胎儿窒息。
规格：注射液：每支１０ｍｇ（１ｍｌ）、２０ｍｇ（１ｍｌ）、４０ｍｇ（１ｍｌ）。
类别：镇痛药\阿片受体激动药
英文名：Alphaprodine
别名： α-普洛丁;阿法罗定;安那度;安侬痛 ,阿那度尔,安那度尔,甲替啶
外文名：Alphaprodine ,α-Prodine, Nisentil, Prisilidene
适应症：
用于需短时止痛(镇痛起效比吗啡迅速,皮下注射5min即见效)，如小手术时以及手术后的止痛，又可与阿托品合用于胃肠道、泌尿道等平滑肌痉挛性疼痛的止痛。
用量用法：
皮下注射：１次１０～２０ｍｇ，１日２０～４０ｍｇ。 静注：１次２０ｍｇ。 极量：１次３０ｍｇ，１日６０ｍｇ。
注意事项：
1.亦有成瘾性，不宜久用。 2.有眩晕、无力、多汗等不良反应。 3.分娩时慎用，可能会引起胎儿窒息。
规格：注射液：每支１０ｍｇ（１ｍｌ）、２０ｍｇ（１ｍｌ）、４０ｍｇ（１ｍｌ）。
类别：镇痛药\阿片受体激动药
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条