1) High energy mills
高能磨
2) high energy ball milling
高能球磨
1.
Influence of process control agent in preparation of SiC/Al composite powder by high energy ball milling;
过程控制剂在高能球磨法制备SiC/Al复合粉末中的作用研究
2.
Influences of high energy ball milling on microstructure and properties of a new steel bonded titanium carbide;
高能球磨对新型TiC钢结硬质合金组织和性能影响的研究
3.
Effects of low temperature heat treatment and high energy ball milling on the preparation of ultrafine alumina;
低温热处理以及高能球磨对制备超细氧化铝的影响
3) High energy milling
高能球磨
1.
Cu-Al alloy powder was produced by high energy milling of Cu and Al, then mixed them together with Cu2O powder,Al2O3/Cu composite was prepared through oxidation and sintering synchronously under the protecting of N2.
采用高能球磨制备出亚稳态的Cu-1%Al(质量分数)合金粉,再将Cu2O粉与其一起进行高能球磨,然后将复合粉末压坯在N2保护炉中同时进行氧化和烧结,制备出Al2O3/Cu复合材料。
2.
A 15%SiC_p/2009Al composite was fabricated by high energy milling powder metallurgy (PM) technique.
采用高能球磨粉末冶金法制备了15%SiCp/2009Al复合材料,研究了球磨转速、球磨时间、加热抽真空工艺、热压成型以及热挤压比对复合材料力学性能的影响。
3.
The aluminum matrix composites reinforced with SiC particulates were fabricated by the high energy milling in conjunction with powder metallurgy.
采用高能球磨粉末冶金技术制备了SiCp/Al复合材料 ,研究分析了该材料界面结构特点。
4) high-energy milling
高能球磨
1.
Influence of high-energy milling on the structure and magnetic properties of atomized magnetic powder;
高能球磨对雾化磁粉结构与磁性能的影响
2.
Micro-nanometer ferric oxide powders were prepared by high-energy milling and then reduction with hydrogen at different temperature for different holding time.
采用高能球磨,制得不同粒度的超细氧化铁粉末,然后,分别在不同还原温度和还原时间下,进行氢气还原。
3.
This paper studed the process and kinetics of solid -state reduction by high-energy milling at room temperature.
采用机械还原的方法以 Si/V_2O_5为原料直接制备 VO_2/SiO_2复合陶瓷粉,主要探讨了高能球磨实现固相反应的动力学条件。
5) high-energy ball milling
高能球磨
1.
Research on preparation of nitrogen-contained stainless steels by high-energy ball milling and sintering;
高能球磨及烧结制备含氮不锈钢的研究
2.
Preparation,microstructure and properties of Cu-15wt%Cr alloy by high-energy ball milling;
高能球磨制备Cu-15wt％Cr合金及其微观组织与性能的研究
3.
Investigation on Al_2O_3-Y_2O_3 mixtures prepared by high-energy ball milling;
高能球磨Al_2O_3-Y_2O_3粉体混合物的研究
6) high energy ball-milling
高能球磨
1.
In addition,the influence of the high energy ball-milling on the PIM and the performance of the alloy was studied.
本次实验以羰基铁粉和羰基镍粉为原料粉末,采用注射成形方法制取Fe-50%Ni软磁合金,研究了高能球磨制备粉末对注射成形工艺以及材料性能的影响。
2.
36 ~23 μm, whose relative density is above 95%, were prepared by a conventional ceramic process using the sol-coating and high energy ball-milling method.
利用溶胶包覆和高能球磨的方法,经传统的陶瓷工艺,得到相对密度在95%以上,晶粒尺寸在0。
3.
TiC,TiN and WC ultrafine powders were respectively prepared from micrograded TiC,TiN and WC raw powders by high energy ball-milling under different ball/powder weight ratio and ball-milling time.
对Ti(C,N)基金属陶瓷硬质相TiC、TiN、WC原料粉在不同球料比、不同球磨时间试验条件下进行高能球磨,探讨了TiC、TiN、WC粉体的高能球磨超细化机理和球磨行为特征。
补充资料：绝对可磨度(见矿石可磨度)
绝对可磨度(见矿石可磨度)
absolute grindability
Juedu一kemodu--一’一一一z，1」一二一」_L:1;十、、口犷绝对可磨度(absolute gr‘ndab‘l‘ty，兄刁石可磨度。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条