1) Sauter diameter
Sauter直径
1.
Based on the dynamic equilibrium principle of the surface chemical reaction rate and the mass transfer rate in liquid liquid phases, the average liquid drop diameter(Sauter diameter) in liquid liquid turbulence system was determined in five geometrically similar nitration reactors installed double coil under different conditions.
根据界面化学反应速率和传质速率的动态平衡理论 ,在五个几何相似的具有双排蛇管的模拟硝化反应器中 ,测定了不同工况下液液湍流搅拌分散系统的Sauter直径。
2.
The average liquid-drop diameter(Sauter diameter) in liquid-liquid turbulence system and residence time distribution(RTD) of fluids in solid-liquid mixing system were determined in five geometrically similar nitration reactors installed double coil under different conditions.
在 5个几何相似的具有双排蛇管的模拟硝化反应器中 ,测定了不同工况下液液湍流搅拌分散系统的Sauter直径和固液混合系统两相的停留时间分布 (RTD)。
2) Sauter mean diameter
Sauter平均直径
1.
By the stochastic approach of Monte Carlo simulation the drop size distribution and Sauter mean diameter d_ 32 in turbulent agitated liquid-liquid dispersions were obtained.
同时通过MonteCarlo模拟的随机方法,得到了湍流搅拌槽中液-液分散体系的液滴直径分布和Sauter平均直径d32。
2.
The particle mean diameters, volume mean diameters and Sauter mean diameters of powders increase with .
在一定的条件下 ,输液管内径越大 ,输液管突出长度越长 ,锌粉的平均粒度dm、体积平均直径dVm和Sauter平均直径dVs越大 ,即颗粒越粗 ;雾化压力越大 ,液锌的过热度越高 ,dm,dVm和Sauter平均直径dVs越小 ,即粉末越
3.
The lognormal distribution was used as model of oil drop size distribution and an analytical expression of Sauter mean diameter was derived from this model.
以对数正态分布密度函数为油滴尺寸的分散模型,导出了油滴的Sauter平均直径解析式。
3) SMD (Sauter mean diameter)
SMD(Sauter平均直径)
4) Sautur mean diameter of droplet
Sauter平均粒径
5) diameter
[英][daɪ'æmɪtə(r)] [美][daɪ'æmətɚ]
直径
1.
Test Analyses of Diameter Matching of Front Top Roller and Back Top Roller of Spinning Frame;
细纱前后档胶辊直径搭配试验分析
2.
Spinning Test of Big Diameter Spinning Top Roller;
大直径细纱胶辊纺纱试验
3.
The result of the wool yarn fault by the Uster evenness testerand the contrast analysis of the surface diameter;
电容式条干仪与表观直径实测毛型纱线疵点的对比
6) diameters
[英][dai'æmitə] [美][daɪ'æmətɚ]
直径
1.
The measurement and extraction of the section profile features of cylinders are the basis of the evaluation of their diameters,form & position errors and roughness.
圆柱体截面轮廓要素的测量与提取是圆柱体直径、形位误差和表面粗糙度评价的基础。
2.
In this paper,We give odd strong harmonious labeling of trees whose diameters are four.
给出了直径为4的树的奇强协调标号。
3.
At present,there are many methods to produce the multi-differences mixture yarn,but to produce through one spinneret is more economical and with better effects compared with other methods,so the influences of the diameters of the die-spin- ning nozzles o.
研究了同板多异涤纶 POY 的单丝细度及取向度与喷丝孔直径的关系, 得到第一,单丝直径与喷丝孔直径的平方成线性关系,单丝线密度与喷丝孔直径的四次方成线性关系;第二,与粗的单丝相比,细的单丝表现出更高的取向度。
补充资料：当量比表面直径、表面积体积平均直径
分子式：
CAS号：
性质：又称当量比表面直径、表面积体积平均直径。是颗粒群表面积分布的平均直径。其意义为与颗粒群的粒形相同，总体积相同、总表面积相同，且粒度均匀的一个假想颗粒群的粒度。亦即指与该颗粒群的粒形相同，比表面积相同的一个颗粒的粒度。
CAS号：
性质：又称当量比表面直径、表面积体积平均直径。是颗粒群表面积分布的平均直径。其意义为与颗粒群的粒形相同，总体积相同、总表面积相同，且粒度均匀的一个假想颗粒群的粒度。亦即指与该颗粒群的粒形相同，比表面积相同的一个颗粒的粒度。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条