1) heating method
加热方法
1.
Research on heating-spinning mould design and the heating method for tungsten plate;
钨板加热旋压模具设计及加热方法研究
2.
Different heating methods and time directly affect the taste and resilience of the finished fish balls.
不同的加热方法和加热时间将直接影响到成品鱼圆的口感和弹性。
3.
This paper expounds the factors causing the oxidizing defect, decarburizing defect, overheating defect, over- burning defect and internal-cracking defect, and points out that the proper and reasonable heating method can avoid the heating defects, improve the quality of the products, reduce the material consumption, and maximize the utilization ratio of the equipments and personnel.
阐述了锻造中产生氧化缺陷、脱碳缺陷、过热缺陷、过烧缺陷、内部开裂缺陷的因素,指出正确合理的加热方法能避免加热缺陷,提高产品质量,降低物资消耗,最大限度地提高设备、人员的利用率。
2) Low-temperature heating method
低温加热方法
3) hot plastic processing method
热塑性加工方法
5) heat distortion test method
加热变形试验方法
6) heating methods
加热方式
1.
The small-diameter lumbers of Daimyo Oak(Quercus dentata) were dried with consecution-heat method and intermittent-heating methods(intermittent 2h and intermittent 6h) to study the occurred stress of surface layer of them during conventional drying process.
结果表明,随着试材的含水率降低,其表层全应力最初表现为拉应力,拉应力增大到最大值后,逐渐减小直至消失,然后转变为压应力,压应力达到最大值后,逐渐减小直到干燥结束;残余应力是先逐渐增大,达到最大后又减小;3种加热方式下,试材表层应力的变化趋势基本一致,但是试材的表层应力间歇加热的明显小于连续加热的,间歇6h试材的表层应力最小;同一含水率水平下,表层应力弦切板的比径切板大。
2.
The results showed that the change of tress of surface layer with three kinds of heating methods were in a similar way.
研究小径木白桦锯材在连续加热方式和间歇加热方式(间歇2h和间歇6h)干燥过程中表层应力的产生、发展变化规律。
3.
The dechlorination of PVC by thermal decomposition with different heating methods and carrier gas characteristics were studied.
为了使含氯废塑料能喷入高炉必须进行脱氯处理 ,研究了热解脱氯时加热方式及载气性质对脱氯率的影响。
补充资料：不同加热方法的干燥设备的适用范围
使微量热空气通过搅拌型间接干燥机与物料剧烈接触，所需热量的90%用间接干燥法提供。该方法适合大批量处理热敏性物料。
利用直接干燥法的流化床干燥机设有间接的热交换器进行床内加热干燥，所需热量的70%用间接加热提供。这样可以更好地发挥直接干燥法的特点。这种方法特别适合大批量处理粉粒体物料。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条