1) Flat Gating System
脊背扁平浇注系统
2) non-balance runner system
非平衡浇注系统
1.
For an one-mold eight-cavity with non-balance runner system,the process of balance runner system was obtained through optimum divided runner size with MPI.
针对一模八腔的非平衡浇注系统,运用MPI技术,给出了通过优化分流道尺寸来获得平衡的流道系统的过程,结合模拟分析结果对分流道尺寸作出修改,最终得到了分流道尺寸的最佳值,从而保证熔体能够基本上同时充满型腔,实现浇注系统的人工平衡,提高了一次试模的成功率。
3) pouring system
浇注系统
1.
Study of the calculating formulas in the minimum section of the gray casting iron pouring system
灰铸铁件浇注系统最小截面积计算公式研究
2.
The injection molding flow of six different pouring system for air-condition panel was analyzed respectively by using Molding Plastics Advisers (MPA)software.
利用模流分析软件Moldflow Plastics Advisers(MPA)对空调机面板注塑模6种构型不同的浇注系统分别进行注射成型流动分析。
3.
The structural characteristics of the aluminum alloy tap part were analyzed, and the design of pouring system and die-casting die structure were introduced.
分析了铝合金水龙头零件的结构工艺性特点,介绍了压铸模的浇注系统及模具结构设计。
4) gating system
浇注系统
1.
Simulation and optimization of gating system of die-casting die for magnesium alloy AM60B part;
AM60B镁合金压铸模浇注系统的模拟与优化
2.
Principle of Designing Gating System for Die Cast Aluminum Alloy Mould;
设计铝合金压铸模具浇注系统类型的原则
3.
Optimization of Gating System for Gear Box of the Car Based on CAE System;
基于CAE分析的汽车齿轮室浇注系统的优化
5) runner system
浇注系统
1.
Design of runner system of injection mould for cellphone glass block;
手机镜片注射模浇注系统设计
2.
Manmade balanced design and numerical simulation for unbalanced runner system;
非平衡浇注系统的人工平衡设计与数值仿真
3.
Optimization of front bumper runner system and its implementation
汽车前保险杠浇注系统优化及实施
6) feed system
浇注系统
1.
Research and development on knowledge-based feed system for injection mould;
基于知识的注塑模浇注系统的研究与开发
2.
Research on the Intelligent Design Technology of Injection Mould Feed System Based on Knowledge;
基于知识的注塑模具浇注系统智能化设计技术研究
3.
Optimization of feed system and design of injection mould for automotive engine cover
汽车发动机罩盖浇注系统优化与注射模设计
补充资料：脊背强
脊背强
脊背强 证名。脊椎肌肉、筋脉强急之证。见《备急千金要方》卷二十。因督脉、膀胱经脉病变所致。《杂病源流犀烛》：“脊背强，《灵枢》云，督脉之别，名曰长强，其病实，则脊强。又曰，足太阳之脉病，则腰脊强痛。此脊背强所由来也。”参见脊强、背痛条。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条