1) green density
生坯密度
1.
The results show that more green density causes more densification but less linear shrinkage and higher burnout temperature causes more densification but less densification rate.
发现生坯密度越大,排蜡后绝缘子线收缩越小,致密化程度大大提高;随排蜡温度升高,绝缘子致密化程度增大,致密化速率减小。
2.
The effects of impact energy and compaction methods on the green density,the maximal impact force,the withdraw force and the radial springback were discussed.
采用高速压制技术制备铁基制品,探讨了冲击能量及冲击速度与冲击行程之间的关系,并研究了冲击能量、压制方式对生坯密度、最大冲击力、脱模力和径向弹性后效的影响。
3.
The effects of impact energy and impact times on the green density, the maximal impact force and the withdraw force of specimen were investigated.
研究电解铜粉高速压制成形工艺,探讨冲击能量、压制次数对生坯密度、最大冲击力和脱模力的影响。
2) compact density
生坯密度
1.
Associated with the massproduction of sintered Nd-Fe-B magnets currently in China,an investigation is presented in this papers of the impact of compact density on microstructure and magnetic properties of sintered Nd-Fe-B magnets.
结合国内烧结 Nd— Fe— B磁体工业生产过程 ,研究了压制成型时生坯密度变化对烧结 Nd—Fe— B磁体致密化程度、显微组织、取向度与磁性能的影响。
2.
Associated with the mass-production of sintered Nd-Fe-B magnets currently in China, an investigation is presented in this paper of the impact of compact density on microstructure and magnetic properties of sintered Nd-Fe-B magnets.
结合国内烧结Nd-Fe-B磁体工业生产过程,研究了压制成型生坯密度对烧结Nd-Fe-B磁体致密化程度、显微组织、取向度及磁性能的影响。
3) threshold compact density
临界生坯密度
4) green apparent density
生坯表观密度
5) green density
压坯密度
1.
Warm compaction behavior of 316L stainless steel was investigated, influences of processing parameters of warm compaction on green density of 316L stainless steel were studied.
研究316L不锈钢的温压行为,分析温压工艺参数对压坯密度的影响。
2.
It is found that the green density and sintered density of YBa_2Cu_3O_(7-δ) powders with different granularity varied differently with the variation of pressure.
结果表明,不同粒度YBaCuO超导粉体的压坯密度、烧结密度(即烧结前后的致密度)随压力的变化规律不同。
3.
Influences of processing parameters of warm compaction on green density of 420 stainless steel were studied.
对420不锈钢粉末进行温压,探索温压工艺参数对压坯密度的影响,并对温压与室温模压(添加0。
6) compact density
压坯密度
1.
The effect of compact density on combustion synthesis of Fe-V-C mixture powders based in electric field was studied using Gleeble thermal simulation equipment.
采用Gleeble热模拟机,在电场和大热流密度作用下,研究压坯密度对Fe-V-C三元系粉末压坯燃烧合成的影响。
2.
Using Gleeble-1500D thermal simulation equipment, the effect of compact density on the low temperature combustion synthesis process of the compact of 55wt%(Ti+C)-45wt%Fe mixture powders was studied.
采用Gleeble-1500D 热模拟机,在电场和大热流密度作用下,研究压坯密度对55%(Ti+C)-45%Fe(质量分数)粉末压坯低温燃烧合成过程的影响。
3.
The paper analyzed the effect of sintering temperature,ball milling method and compact density on the density of MoSi2 disperslion-strengthened copper alloy.
分析了烧结温度、球磨方式和压坯密度对MoSi2弥散强化铜合金烧结密度的影响。
补充资料：实坯坯
1.见"实丕丕"。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条