1) bonded NdFeB permanent magnet
粘结NdFeB永磁体
1.
The protection technology of electroless Ni-Cu-P alloy plating on bonded NdFeB permanent magnets was studied, and a feasible technological process and a coating with high corrosion resistance were obtained.
对粘结NdFeB永磁体化学镀Ni Cu P合金防护层的工艺过程及镀层的阻氢性能进行了研究。
2.
The protection technology of electroless NiCuP alloy plating on bonded NdFeB permanent magnets was studied.
研究了粘结NdFeB永磁体化学镀Ni Cu P合金防护层的工艺过程。
2) bonded NdFeB magnet
粘结NdFeB磁体
1.
Preparation technology of the bonded NdFeB magnet;
粘结NdFeB磁体的制备工艺
2.
Effect of forming technology on mechanical properties of bonded NdFeB magnet;
成型工艺对粘结NdFeB磁体力学性能的影响
3.
Effect of presing processes on structure and magnetic properties of the bonded NdFeB magnet;
成形工艺对粘结NdFeB磁体结构和磁性能的影响
3) NdFeB bonded magnet
NdFeB粘结磁体
1.
Study on properties of anisotropic NdFeB bonded magnet produced by molding compression
模压成形各向异性NdFeB粘结磁体性能研究
2.
The effect of particle size and its distribution of magnetic powder and different antioxidant on magnetic properties of NdFeB bonded magnets by injection moulding is studied.
本文研究了磁粉的粒度分布以及不同抗氧化剂的加入对注射成型NdFeB粘结磁体密度和磁性能的影响。
3.
ABSTRACT: The addition of different additives taking an effect on the properties of NdFeB bonded magnets byinjection moulding.
本文研究了各种添加剂的加入对注射成型NdFeB粘结磁体性能的影响。
4) bonded NdFeB magnets
粘结NdFeB磁体
1.
The characters of three kinds of binders for bonded NdFeB magnets are studied at room temperature and high temperature.
研究了三种适合模压粘结NdFeB磁体的粘结剂的室温和高温特性 ,其中一种为GBM -H型 ,室温抗压强度为 180N/mm2 ,韧性也很好 ,可在 12 0℃以下温度使用 ,时效期超过 6个月 ,是一种适合规模生产粘结NdFeB磁体的粘结剂 ;另一种GBM M粘结剂的室温和 2 0 0℃温度下的抗压强度都为 2 30N/mm2 ,是一种耐温可达 2 0 0℃以上的粘结
5) NdFeB bonded magnets
NdFeB粘结磁体
1.
NdFeB bonded magnets are prepared by the three kinds of different mezzo epoxy value binder in the paper,law and mechanics of magnets magnetic properties and compressive strength are studied by binder mezzo epoxy value.
本文采用三种不同环氧值的粘结剂制备了NdFeB粘结磁体,研究了粘结剂环氧值影响磁体磁性能及抗压强度的规律及其机理。
6) sintered NdFeB permanent magnet
烧结NdFeB永磁体
1.
Electroless Ni-P/TiO2 composite coating was prepared on sintered NdFeB permanent magnet using electrolessnickel plating and sol-gel technique.
采用化学镀镍和溶胶-凝胶成膜技术,在烧结NdFeB永磁体表面形成了Ni-P/TiO2复合膜,XRD分析结果表明,复合膜为非晶态结构。
补充资料:烧结稀土永磁体
烧结稀土永磁体
烧结稀土永磁体
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条