1) expansion body
膨胀心头
1.
Analysis shows that, under the same working condition, the impellent required in the casing expension with single-stage expansion body is less than that with multistage expa.
根据弹塑性有限元理论 ,建立了膨胀套管和膨胀心头的力学模型。
2) expansion core
膨胀芯头
1.
According to the elastic-plastic theory, the calculation method of tangential stress , radial stress of expansion casing both in elastic deformation area and in plastic deformation area is deduced and the minimum critical load between expansion core and casing was determined.
根据弹塑性的理论,推导了膨胀套管在弹性变形区和塑性变形区的周向应力和径向应力计算模型,确定了膨胀套管膨胀时在膨胀芯头与套管之间所需的最小接触载荷。
3) expansion bend
膨胀弯头
1.
Design and analyzing of expansion bends in deck piping of ships;
船舶甲板管系膨胀弯头的设计分析
4) expansion junction
膨胀接头
1.
Analysis to samples for arranging and setting of expansion junctions in diesel discharging pipes;
柴油机排气管中膨胀接头的布置与安装实例分析
5) expansion clamp
膨胀卡头
6) expansion center
膨胀中心
1.
For the stress analysis of large-scale utility boiler pipeline, expansion center must be adopted.
大型电站锅炉管道的应力分析,必须设有膨胀中心。
2.
The paper reports on an improvement of the elaborated model, for calculating expansion centers and taking the NG 410/9.
该文对以前建立的膨胀中心计算模型做了改进 ,并以NG 410 /9。
3.
According to imported CE technogy, the sealing design of boiler depends on the proper location of boiler expansion center and reliable stress analysis, and the reliable mode of sealing design is thus spelt out for large capacity boilers while criteria were proposed for selection of material through analysis of insulation construction of wall and properties of material used.
根据CE引进技术 ,把锅炉密封设计建立在锅炉膨胀中心的设立和可靠的应力分析计算基础上 ,从而提出大容量锅炉可靠的密封设计模式 ,同时对炉墙保温结构及其材料性能进行了分析 ,提出了选用意见。
补充资料：片片心头肉
主料： 猪心1个，梅头肉（柳梅）1条，大红肠1/2条，油（起锅）2汤匙，糖2汤匙，白醋1汤匙。
配料： 腌料：酱油100ml，蒜头（拍烂）4粒，酒3汤匙，五香粉2汤匙，麻油、胡椒粉各少许。
做法： 1、将猪心、柳梅及大红肠洗净后全部一开二。
2、腌猪心及柳梅约2小时。
3、用油起锅后，倒入猪心及柳梅略爆（连汁），再加清水至刚盖过肉面，用中至大火焖至水分剩1/2时，加入红肠同焖（须不时略兜）。
4、当汁收水时，加入糖及白糖兜匀，改以小火煮至汁干及浓稠。
5、切小片排好上碟即成。
备注： 煮菜一定要一边煮，一边试味，不能单调地跟足书本上的步骤去做，在多番尝试下灵活变通，煮出来的菜才出色味美。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条