1) CPSBRL
羧基丁苯吡胶乳
1.
Study on Preparation and Properties of CPSBRL;
羧基丁苯吡胶乳的合成及其性能研究
2) carboxylated styrene butadiene latex
羧基丁苯胶乳
1.
Nylon short fiber grafted rubber composites was prepared when short fiber pretreated with γ -methacryloxy propyl trimethoxy silane(A 174) or γ -amino propyl triethoxy silane(A 1100) was soaked in carboxylated styrene butadiene latex for 10 min , then was kept in an oven at 110 ℃ for 90 min .
将用γ-(甲基丙烯酰氧基)丙基三甲氧基硅烷(A174)或γ-氨丙基三乙氧基硅烷(A1100)处理后的尼龙短纤维分别加入到特软羧基丁苯胶乳中,浸泡10min后于110℃烘箱中干燥90min,可制备尼龙短纤维接枝橡胶复合材料。
2.
Two methods were used to analyze the distribution of carboxylated styrene butadiene latex in the coating layer,one is energy dispersive X ray spectrometer,the other is backscattered electron(BSE) imaging after treating the sample by standard metallographic techniques.
运用两种方法对经溴标记的涂布纸中羧基丁苯胶乳在涂层内的分布进行了检测。
3) carboxylated styrene-butadiene latex
羧基丁苯胶乳
1.
Research on freeze-thaw stability of carboxylated styrene-butadiene latex;
羧基丁苯胶乳冻融稳定性研究
2.
Physical and chemical behavior of YH-05, Dow-675, SD-656 carboxylated styrene-butadiene latex in paper coating are discussed.
讨论了羧基丁苯胶乳物化性能对铜版纸涂布性能的影响,对比了YH-05、Dow-675、SD-656三种羧基丁苯胶乳的成纸性能。
3.
The indexes of domestic carboxylated styrene-butadiene latex for paper coating were compared and the imported latexes used in paper coating were analyzed.
对比了现有国内生产造纸用羧基丁苯胶乳的各项指标 ,剖析了国内高速涂布纸生产厂家所用的进口胶乳 ;探讨了高速涂布纸用胶乳的性能要求 ,确定小粒径、良好的机械稳定性和化学稳定性是高速涂布纸用胶乳的重要特点。
4) carboxylated styrene-butadiene rubber latex
羧基丁苯胶乳
1.
By means of the enlargement rules and the test data for the carboxylated styrene-butadiene rubber latex(XSBRL)polymerization reactor proposed from the experiments in pilot plant and demonstration plant, the reactors used in the commercial production were designed, and the heat transfer in the react ors and the question in enlarging the styrene devolatilizer of latex were researched.
利用羧基丁苯胶乳中试和工业试验提出的聚合釜的放大规律和试验数据，以工业化为目标，分析了聚合釜的传热和脱气釜的放大问题，比较了２０ｍ３、３０ｍ３聚合釜放大的技术成熟性和两种结构不同的脱气釜的脱气性能。
2.
The enlargement rules of polymerization reactor for the synthesis of carboxylated styrene-butadiene rubber latex was studied based on the features of its synthesis process,homogeneous nucleation of emulsion and low-soap polymerization by the experiments on cold model and commercial plant.
根据羧基丁苯胶乳合成工艺的特点、乳液均相成核机理和低皂聚合原理，拟定了设计聚合釜的放大规律应遵循的依据。
3.
The effects of agitation power, agitation speed, agitation grade and heat transfer ability on polymerization temperature and product quality in the production of carboxylated styrene-butadiene rubber latex in 12.
０ｍ￣３聚合釜在生产羧基丁苯胶乳中搅拌功率、搅拌级别、桨叶端速和传热能力对聚合温度及产品质量的影响。
5) carboxylic styrene butadiene latex
羧基丁苯乳胶
6) SBR latex
羧基丁苯胶乳
1.
Introduced the development and application of SBR latex used in papermaking.
介绍了新型羧基丁苯胶乳的开发与应用,乳化剂的复配及搅拌转速对胶乳生产的影响,并通过对比验证了该产品的优良性能。
2.
Introduced the reasons of gel\'s formation which were attached to the SBR latex polymerizers currently and their effects on industry.
综述了当前羧基丁苯胶乳聚合釜挂胶形成的主要原因及影响,介绍了常用的清洗方法及各自的利弊,并对其前景进行了展望。
补充资料：丁苯吡胶乳
分子式：
CAS号：
性质：丁二烯、苯乙烯和2-乙烯基吡啶经乳液共聚制得的三元共聚物胶乳。共聚时它们的配比是丁二烯：苯乙烯：2-乙烯基吡啶=75:15:15。以松香酸皂和萘磺酸甲醛缩合物作乳化剂，过硫酸盐-亚硫酸氢钠作氧化还原引发剂，从40～70℃升温聚合，聚合时间30～40h，转化率接近100％。丁苯吡胶乳与间苯二酚、甲醛配成处理乳液用于帘布浸渍。它是还是合成纤维与橡胶优良的胶黏剂，其主要用途是帘线浸渍制造轮胎、运输带和胶管。
CAS号：
性质：丁二烯、苯乙烯和2-乙烯基吡啶经乳液共聚制得的三元共聚物胶乳。共聚时它们的配比是丁二烯：苯乙烯：2-乙烯基吡啶=75:15:15。以松香酸皂和萘磺酸甲醛缩合物作乳化剂，过硫酸盐-亚硫酸氢钠作氧化还原引发剂，从40～70℃升温聚合，聚合时间30～40h，转化率接近100％。丁苯吡胶乳与间苯二酚、甲醛配成处理乳液用于帘布浸渍。它是还是合成纤维与橡胶优良的胶黏剂，其主要用途是帘线浸渍制造轮胎、运输带和胶管。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条