1) inner blind hole perforator
![点击朗读](/dictall/images/read.gif)
内盲孔射孔器
1.
This paper introduces the criterion of selecting pump, detonation mode, principle and action of inner blind hole perforator and tubing pump joint technology.
介绍了内盲孔射孔器与管式泵联作技术的选泵标准、起爆方式、原理和流程以及内盲孔射孔器的研制。
2) inner blind hole
![点击朗读](/dictall/images/read.gif)
内盲孔
1.
From feasibility of inner blind hole perforator, the paper analyses its outstanding advantages compared with outer blind hole perforator.
本文从内盲孔射孔器的可行性入手,分析内盲孔射孔器与外盲孔射孔器相比所具有的突出优点,对射孔器的加工工艺方案设计及打靶试验情况进行了说明。
3) blind hole
![点击朗读](/dictall/images/read.gif)
盲孔
1.
Applied formula of nickel eletroplating additive for deep and blind hole;
![点击朗读](/dictall/images/read.gif)
深孔盲孔镀镍添加剂应用配方探讨
2.
Discussion on estimating the blind hole during chemical grouting;
![点击朗读](/dictall/images/read.gif)
化灌中对盲孔判定问题的探讨
3.
Building blind hole structure analyzer of the oil perforating gun based on BP neural network;
基于BP神经网络建立石油射孔枪盲孔结构分析器
4) Micro-pore
![点击朗读](/dictall/images/read.gif)
盲孔
1.
An opto-electronic inspection system based on the direct imagery theory is presented for non-contact observation of the micro-profile of a small area, especially that of the underside of a micro-pore.
针对微小面积,特别是微小"盲孔"底面形貌的非接触精密检测,提出了一种基于直接成像原理的光学结构。
5) blind via
![点击朗读](/dictall/images/read.gif)
盲孔
1.
The investigation on the cracking morphology of the blind vias and chemical analysis on the grain boundary of copper - plating layers have definitely identified that inappropriate compositions of electroplating solution and sulfur segregation are the critical causes of the crack defect.
通过观察盲孔的开裂形貌、分析裂纹的化学成分,确认了镀液配比不当、硫等杂质元素偏析是引起开裂缺陷的关键起因,并首次提出了开裂的失效机制。
2.
Failure of blind via is one of the main causes of an open circuit in printed circuit board(PCB).
盲孔开裂是导致印制电路板(PCB)电气断路的主要原因之一。
6) inner jet hole
![点击朗读](/dictall/images/read.gif)
内喷射孔
补充资料:内射对象
内射对象
infective object
内射对象flnj眯幽e硕沁t;11眼。脚诚。触盯] 一个Ab日范畴(Abellan category)C中一个对象I,使对任何单态射献A‘1~A,映射Homc(A,I)~Hom。(A’,I),其中职‘一毋。:,都是满的,一个对象A的每一个内射子对象I都是A的一个收缩.内射对象的积是一个内射对象.如果在C中每一个对象都同构于C中一个内射对象的一个子对象,就说C是一个具有足够内射对象的范畴(以-记gory俪 thenol」gllinjeCtiveo切戊怡)(例如G拍山“戚法土范畴(Gro廿止ndieCk Oltegory)就具有此性质).在这样的范畴中,一个对象是内射的当且仅当它是包含它的任一对象的直和项.对于这种范畴的对象,可以构造由内射对象所组成的分解式(内射分解(injeCti记渭。lu-tio招)).这就使得可在这些范畴中发展同调代数. 在局部NOether范畴(见拓扑化的范畴(topol叩-刘口记即口))中,内射对象的直和也是一个内射对象,而且每一个内射对象都同构于不可分解的内射对象的直和而且此表示式是唯一的(13」).如果c是一个N沈ther交换环A上的模范畴,那么,不可分解的内射模就是商环A/p的分式域的内射包,这里p是人中任意的一个素理想(t4】). 例1) Abel群的范畴有足够内射对象,这些对象就是完全(可除)群. 2)右A模的范畴C人包含足够的内射对象(见内射模(inj以泪Ve module)). 3)在一个戴环拓扑空间(X,份)上的模的层的范畴包含着足够的内射对象.这种对象的例子是这样的层F,其所有的茎F二都是内射价,二模.如果(X,心)是一个概形(schen亡),对于拟凝聚价,二模,其逆也真:一个内射层的每一个茎都是一个内射心,二模.【补注】内射对象可以在非Abel范畴中研究(这常常是很重要的).例如S沥Iski定理(S沥rskiU篮幻咖)【AI]刻画完全Bool代数为R刀1代数与R阅1同态的范畴中的内射对象(而Mac卜化沮e完全化构造(见(偏序集中的)加肠沙抽业完全化(印mpletion,入肠ch记几七))在这个范畴中提供了内射包).在一个拓扑斯(tolx万)中,一个对象是内射的,当且仅当它恰好是某幂对象的一个收缩,而内射对象在相应的层函子的研究(见【A2」)中是用到的.
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条