1) Engineering method
工程法
1.
Aiming at rolling of cored welding strip, based on the reasonable hypotheses, mathematics models of parameter, such as average unit pressure , belting thickness by rolling, advancing slip value are derived through making use of engineering method.
针对药芯焊带轧制实际 ,本文在合理假设的基础上 ,利用工程法推导出药芯焊带轧制的平均单位压力、包带轧后厚度、前滑值等轧制参数的计算数学模型 ,借助计算机对该数学模型求数值解 ,并用实验进行验证 ,数值解与实验值具有吻合较
2.
Analyzed asynchronous rolling characteristic,based on the different deformation zone according to different deformation plastic formula,deduced rolling pressure formula using engineering method,and approved its accuracy by experiment,supplied theoretical evidence for studying asynchronous rolling.
分析了异步轧制的轧制特点,根据不同的变形区不同的塑性方程,采用工程法推导了异步轧制的轧制压力计算公式,并通过实验证明了公式的准确性,为异步轧制的研究提供了理论依据。
2) Engineer's method
工程师法
3) engineering method
工程方法
1.
Prediction of initiation moment of pressure pipe containing through-wall crack by EPRI engineering method;
用EPRI工程方法预测含裂纹钢管起裂载荷
2.
An engineering method for the fatigue crack propagation reliability analysis of diesel engine crankshaft;
曲轴疲劳裂纹扩展可靠性分析的工程方法
3.
An engineering method for calculation of cyclic J integral is proposed, according to the handbook of stress intensity factors and using the full plastic solution of EPRI for fracture.
分析了循环Ｊ积分与ＲｉｃｅＪ积分数学形式上的相似性，提出了据应力强度因子手册和利用ＥＰＲＩ弹塑性断裂分析全塑性估算解计算ΔＪ的工程方法。
4) project of subtraction
减法工程
5) engineering methods
工程方法
1.
In this part, the author discusses the function and characteristics of universities and the pedagogy of the engineering methods.
在这部分中笔者结合教学考察的体会 ,讨论了大学的作用与性质 ,工程方法的教学等问题。
6) engineering method
工程算法
1.
An engineering method for calculating transient surface heat flux and surface temperature of hypersonic vehicle is described in this paper,including stagnation point and out of stagnation point.
采用工程算法,包括驻点和非驻点的瞬态表面热流和温度的计算以及完全气体和平衡气体条件下边界层外缘参数的计算。
2.
A engineering method,which accounts for variable entropy effects by modifying momentum thickness is described in this paper.
采用动量厚度来修正变熵效应的工程算法,并以15°钝锥为例,对其表面热流进行了计算,将计算结果与试验值进行了对比,结果吻合良好,表明该工程算法,方便简捷,计算量小,且有足够精度,可为高超声速飞行器初步设计热环境计算和防热材料的合理选择提供可靠的参考数据。
补充资料：坦克维修工程车(见坦克保养工程车、坦克修理工程车)
坦克维修工程车(见坦克保养工程车、坦克修理工程车)
tank maintenance %26 repair vehicle
一““、、’v‘丈人1以gUflgCnengChe坦克维修工程车(:artk Inaintenane。%26repair vehicle)装有坦克维修设备、仪器、工具的技术保障车辆。见坦克保养工程车、坦克修理工程车。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条