1)  alloy steels
合工钢
2)  combination of labor
合工
1.
With the rise of theory on Business Process Reengineering and Project Management, the theory of "division of labor" is claimed to be outdated and that it should be substituted by the theory of "combination of labor".
随着BPR和项目管理在企业管理中的兴起 ,出现了用“合工”思想替代“分工”理论的说法 ,并称“分工”理论过时了。
3)  coupling process
耦合工艺
1.
Study on catalytic distillation coupling process of isobutene oligomerization;
异丁烯齐聚反应精馏的耦合工艺研究
4)  composite process
组合工艺
1.
The printing and dyeing wastewater was treated by a pulse cyclic fluidized bed(CFB) composite process with engineering scale of 5000m3/d.
采用脉冲循环流化床与物化沉淀池的组合工艺对某公司的印染废水进行了处理。
2.
Composite process composed of inorganic macromolecule flocculent polymeric ferric sul-fate (PFS) with leading effective microorganism (EM) was used for algae control of raw water from eutrophic water body.
结果表明:组合工艺在最佳工作条件下,即PFS为30 mg/L,VEM/V污水为5/10 000,曝气时间为HRT/2(HRT=5 d),水温为25℃,pH为中性时,原水中叶绿素a,TP,COD,TN的去除率分别可达93%,89%,85%,60%。
3.
The experimental method of aeration biological filter-chemical precipitation-sand filter composite process and water quality situations in experiment are introduced.
介绍了曝气生物滤池—混凝澄清—砂滤组合工艺的试验方法及其试验用水水质情况,并分析了该工艺对CODCr,NH3-N,总硬度,总磷的去除效果,得出了一些有意义的试验结论,为中水回用工程设计提供了可靠的参数。
5)  Combined Technology
组合工艺
1.
Experimental Study on Treatment of Rural Domestic Sewage by Combined Technology;
农村生活污水处理的组合工艺试验研究
2.
Then the incline plate sediment-continuous filtering-ultrasonic filtering-reverse osmosis combined technology was used to treat wastewater.
用“斜板沉降-连续过滤-超滤-反渗透”这一组合工艺来处理炼油污水,并将处理后的污水回用于锅炉补水。
3.
While gas recovery getting ito the medium and later stage,the combined technology of drainage gas recovery by gas lifting and by foam are developed in order to suit the condition of constantly descending of formation pressure.
在气田进入中后期开采阶段 ,为适应地层压力不断下降的情况 ,又开展了气举与泡排组合工艺的研究、应用试验 ,取得了显著的经济效益。
6)  compound technology
复合工艺
1.
The computation about the thickness ratio of four sheets of metallic strips and the compound technology is presented.
介绍了采用四层金属材料组成的热双金属片的研制过程,给出了四层金属片厚度比的计算方法及四层金属片的复合工艺。
参考词条
补充资料:非合金工具钢

non-alloytoolsteel:含碳很高(0.7~1.35)、实际上不含合金元素的钢(钢种)。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。