1) flexoelectric
挠曲电
1.
The planar aligned nematic liquid crystal cell with the influence of the flexoelectric effect and different anchoring for the two substrates is investigated by an analytical method.
着重考虑了挠曲电效应的影响,导出了指向矢倾角θ满足的微分方程和边界条件,计算和讨论了阈值电压以及指向矢分布对盒中央平面对称性破缺参量Δ。
2) flexoelectric effect
挠曲电效应
1.
The surface physics of liquid crystals and the flexoelectric effect;
液晶表面物理——挠曲电效应研究及进展
2.
Negative liquid crystal MBBA that aligns along the normal to the plates in liquid crystal cell will arise the flexoelectric effect when a external electric field is applied in the plane of slab.
负性液晶MBBA在液晶盒中垂面排列,沿面外加电场后产生挠曲电效应。
3.
Based on the elastic theory of liquid crystal and variation theory, the flexoelectric effect in horizontal oriented LC cell is studied, and the differential equation and boundary condition about the director of liquid crystal are obtained.
基于液晶弹性理论研究了平行排列液晶盒中的挠曲电效应,通过变分理论得到了液晶指向矢满足的微分方程及边界条件。
3) flexoelectric polarization
挠曲电极化
1.
The flexoelectric polarization is considered also but the selective ion adsorp- tion is ignored.
考虑挠曲电极化,但不考虑界面上离子选择吸附产生的极化,文章详细讨论了表面极化P_s对平行向列液晶盒阈值电压和饱和电压的影响。
4) bulk flexoelectric effect
挠曲电体积效应
1.
With elastic theory of liquid crystal,we investigate bulk flexoelectric effect in a nematic liquid crystal(NLC) cell with applied voltage.
基于液晶弹性理论研究了电压作用下向列相液晶盒中的挠曲电体积效应。
5) deflection
[英][dɪ'flekʃn] [美][dɪ'flɛkʃən]
挠度，挠曲
6) flexure
[英]['flekʃə] [美]['flɛkʃɚ]
挠曲
1.
In order to know the low temperature performance of polyfluortetraethylene used as sealing material,the mensuration is done that constriction plate and tubular test piece, and of plate flexure in the range of -100 to -40℃.
为了考查聚四氟乙烯用做密封材料时的低温性能,在-40至-100℃的温度范围内,分别对板状和管状试件的收缩以及板状试件的挠曲进行了测定。
2.
The nonlithostatic stresses, regions of failure and flexure profiles have been computed as the upper crustal layer is extended by progressive increments.
计算了以一定增量逐渐拉伸上地壳层时各个阶段的非静岩应力 (Nonlitho staticstress)、塑性破裂 (Plasticfailure)分布及挠曲剖面 (Flexureprofile)。
3.
Compensating For the Super-Long Precision Rubbing Rollor’s Flexure
对TFT-LCD摩擦设备的超长精密摩擦滚子进行变形量计算和测量,采用切削补偿的方法可以有效地抵消摩擦滚子因自重产生的挠曲变形,提高摩擦质量。
补充资料：厂用电受电
厂用电受电
energizing of auxiliary power system
chongyongd一on sho一Jd一on厂用电受电(energizing of auxiliary powersystem)机组附属设备安装完毕后需通电试运行，所需厂用电源由外部供给，因此厂用电受电是调试工作开始的标志。 受电步骤新建电厂先由电力系统向变电站供电，再依次对高压起动/备用变压器、3~10kv厂用配电装置、厂用工作变压器及380V配电装置供电。扩建电厂因高压起动/备用变压器已经投人运行，故可利用它的电源对扩建的厂用配电装置等供电。 调试项目主要有:①用额定电压依次对空载线路、变电站母线、隔离开关、断瘩器、互感器、变压器及厂用配电装置等进行冲击合闸试验。有条件时.冲击合闸前应先进行递升加压试验。升压过程中注意检查各设备有无放电声及短路现象，发现问题及时处理后再进行升压。②检查三相电压应平衡，相序应正确，各段母线的相位彼此应一致。对配电装置供电时，有时会由于母线电容和与母线连接的电磁式电压互感器的电感相互作用而出现铁磁谐振，此时相电压升高，中性点明显位移。为消除谐振可在电压互感器的剩余电压绕组处并联电阻以去振。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条