1) Bias flow
偏流
1.
The improper control of a direct heated furnace installed at an oil field will give rise to bias flows during its combustion, often resulting in coke formation in the heating tubes, which eventually have to be replaced.
如果控制不当直热炉燃烧过程中会出现偏流现象,将导致加热管内结焦,多次烧焦后就必须更换加热管。
2.
The influence of one-dimension compressible bias flow on the acoustic impedance of perfo-(rated) panels was discussed with consideration of the compressibility of flow.
从理论上研究了一维可压缩偏流对穿孔声阻抗率的影响,并分析了偏流对穿孔粘滞效应的影响;在实验中,利用真空泵流装置建立了存在偏流时的穿孔板声阻抗率测量系统,测量了一定频率范围内两块不同厚度穿孔板在不同偏流流速时声阻抗率的变化规律。
3.
The effect of grazingbias flow interaction on the orifice acoustic impedance has been experimentally investigated.
对切向流和偏流相互干扰如何影响穿孔板声阻抗进行了细致的实验研究,结果表明:切向流削弱了偏流对穿孔板声阻的调控,但在较高偏流速度下,偏流对穿孔板声阻的影响仍起主导作用;此外,不同的偏流方式(吹气或吸气)与切向流干扰对穿孔板声阻抗的影响有明显区别。
2) bias current
偏流
1.
The effects of the deposition parameters such as bias voltage and bias current strength of curved magnetic fields on the DLC films structures are discussed.
分别采用带有和不带有弯曲弧磁过滤器的真空阴极弧离子镀方法,在不同镀膜电流以及不同基片偏流下分别制备了类金刚石碳膜,对比了不同结构下类金刚石碳膜的Raman光谱特点。
2.
A soft trouble of Philips MRI RF amplifier occurred with message -"Bias current out of range" on operating console screen, and the scan stopped.
Ｐｈｉｌｉｐｓ Ｔ５－ＮＴ磁共振设备中的射频放大器出现了偏流超出正常值的软故障，经过测试软件测试，以及进行最大功率调节等处理，最终判定功率放大部件故障，并由替代法证实。
3) deflective flow
偏流
1.
This article analysis the problems commonly existing in several domestic plants which adopt Texaco coal gasification technology,expounds the harm caused by deflective flow of gas in quench chamber,and provides the basis for diagnosis and treatment.
将德士古水煤浆气化工艺在我国已投入运行中的几个厂家遇到的实际问题作一分析，提出反应气在激冷室内偏流的危害和判断处理的依据。
2.
In the flying course of the low-speed revolving rocket,deflective flow willappear due to the nutation effect, the method of calculating the deflective flow based on the exterior ballistics is given, and the simulation result with some examples is also stated.
低速旋转火箭弹在飞行过程中,由于章动因素的影响产生偏流。
3.
Finally,digital simulation shows that radial mass has obvious effect on exterior ballistic parameters,especially for deflective flow.
首先推导了N滑块体系下系统的惯量张量,以双滑块机构为物理模型分别建立了质心平动动力学方程和绕质心转动动力学方程,接着构建了完整的滑块机构设置下系统8自由度方程,最后进行了数字仿真,结果表明径向滑块运动对外弹道影响比较明显,特别是对偏流尤为突出。
4) drift
[英][drɪft] [美][drɪft]
偏流
1.
The range error and drift error are calculated and analysed when the fitting is performed on different firing angle, so that a reasonable fitting region is chosen to decide the firing angle.
对在不同射角下符合时,由射表误差源造成的射程误差和偏流误差进行了计算与分析,论述了符合射角选择的合理区域。
2.
It is shows that the deflection correction can be achieved by reducing scross drift of projectile which is accomplished.
美国专利和年会报告均提到一种低成本的二维弹道修正原理,通过减旋造成偏流减小而降低横向散布。
5) inclined flow
偏流斜流
6) bias
[英]['baɪəs] [美]['baɪəs]
偏压;偏流;偏差
补充资料：创建偏移剖面
要创建偏移剖面，必须通过在“草绘器”中进行草绘以定义切口轮廓。然后，垂直于草绘平面投影此轮廓。单击 
或“视图”(View)>“视图管理器”(View Manager)。“视图管理器”(View Manager) 对话框打开。单击“剖截面”(Xsec)。单击“新建”(New)。出现一个缺省的剖面名称。按 ENTER 键。“剖截面创建”(XSEC CREATE) 菜单打开。单击“偏移”(Offset)>“一侧”(One Side) 或“双侧”(Both Sides)>“完成”(Done)。“选取”(SELECT) 对话框打开。选取草绘平面，并定义查看方向和草绘方向。进入“草绘器”。选取用于尺寸标注的参照图元。草绘剖面轮廓并单击 
退出“草绘器”。 在“视图管理器”(View Manager) 中，单击“显示”(Display)>“设置可见性”(Set Visible)。“可见性”(Visibility) 对话框打开。单击“显示剖面线”(Show X-Hatching) 查看剖面。单击 预览或单击 接受选取的选项。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条