1) UV cured composite coatings
紫外光固化复合涂层
1.
The migration phenomena of nano-SiO_2 particles in UV cured composite coatings are studied by FTIR-ATR and the factors affecting the distributing gradient of nano-SiO_2 particles in coating are discussed by semi-quantitative analysis.
用衰减全反射红外光谱(FTIR-ATR)技术研究了纳米SiO2粒子在紫外光固化复合涂层中的迁移现象,并对影响纳米SiO2粒子在涂层中分布梯度的因素进行了半定量分析。
2) ultraviolet curing coating
紫外光固化涂料
1.
This article has reviewed the application of ultraviolet curing coatings in automotive plastic parts;repair coating;topcoat,and drawn up the development trend of the ultraviolet curing coatings in automotive finishing.
概述了紫外光固化涂料在汽车塑料部件、修补漆、面漆上的应用,并展望了紫外光固化涂料在汽车涂装上的发展趋势。
3) UV curing coatings
紫外光固化涂料
1.
This article is focused on discussion of the influences of monomer for UV curing coatings and its amount,crosslinking monomer,application temperature,curing extent and surface treatment of substrates on the adhesion of the coating film on the plastic substrates.
紫外光固化涂料在表面自由能低的塑料底材上附着极为困难。
4) UV-curable coating
紫外光固化涂料
1.
Synthesis of polymerizable antistatic agents and application in the UV-curable coatings;
聚合活性抗静电剂合成及在紫外光固化涂料中的应用
2.
In this paper, novel UV-curable coating prepared from epoxlidized soybean oil(ESBO) was investigated.
本文对环氧大豆油(ESBO)新型紫外光固化涂料进行了研究,并讨论了光敏涂料的优化配方、光固化工艺以及固化膜的动态粘弹行为。
5) UV-curable coatings
紫外光固化涂料
1.
The UV-curable coatings with good corrosive resistance,heat resistance,abrasive resistance,self-clearing ability and environment protection is prepared with above-mentioned nano activated attapulgite,active diluents,photo initiators,pigments,fillers and other additives.
采用等物质的量的甲苯二异氰酸酯、丙烯酸-β-羟乙酯加成,得到的加成物与纳米凹凸棒表面的羟基官能团再次进行加成反应,生成表面结合双键的纳米凹凸棒中间体,然后与活性稀释剂、光引发剂、颜料、填料和其他助剂复配,制备的紫外光固化涂料具有良好的抗蚀性、耐热性、耐磨性、自洁性和环境友好性。
6) UV curable coating
紫外光固化涂料
1.
Effect of UV Curable Coating on Mechanical Properties of ABS;
紫外光固化涂料对ABS力学性能的影响
2.
According to the demand of cleaner production of the UV curable coating, the synthesis of glycidyl acrylate—the principal part of UV curable coating has been improved.
本文根据紫外光固化涂料(UV涂料)行业清洁生产的要求,改进了现有紫外光固化涂料主体——丙烯酸光敏树脂的合成工艺,并进一步研发出两种新型丙烯酸光敏树脂,在此基础上结合紫外光固化涂料和水性涂料各自的优点研究合成水性丙烯酸光敏树脂,并通过逐步试验确定了每一种树脂的最佳工艺参数,为紫外光固化涂料行业实现清洁生产奠定了理论基础,提供了技术支持。
补充资料：紫外光固化
分子式：
CAS号：
性质：又称光固化或紫外光固化。感光树脂在光敏剂(或称增感剂)存在下，经光照射后，即发生光引发的加成聚合反应，可使线性结构转变为三维空间的网状结构。
CAS号：
性质：又称光固化或紫外光固化。感光树脂在光敏剂(或称增感剂)存在下，经光照射后，即发生光引发的加成聚合反应，可使线性结构转变为三维空间的网状结构。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条