说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 马氏体量
1)  Martensite Volume
马氏体量
2)  martensite content
马氏体含量
1.
Study on relationship between properties and martensite content and size of dual-phase steel;
双相碳钢性能与马氏体含量和晶粒大小关系初析
2.
The research results show that the maximum shear stress of dual-phase steel raises with the increase of martensite content.
研究表明,随着马氏体含量的增加,双相钢的最大剪切应力随之增加。
3)  high-martensite content dual-phase steel
高马氏体量双相钢
1.
The microstructure,tensile properties as well as fracture mechanism of high-martensite content dual-phase steel were studied by OM,SEM and tension test.
通过光镜、扫描电镜分析以及拉伸试验研究了高马氏体量双相钢(马氏体体积分数大于30%)在不同热处理条件下的显微组织和拉伸性能,并进一步探讨了其断裂机理。
4)  martensite transformation bond energetic factor
马氏体转变能量因子
1.
Two new parameters, martensite transformation bond energetic factor and bond strength factor, are proposed to clarify the stability of austenite and the transformation of martensite.
提出用两个新的参数———马氏体转变能量因子和键强因子来考察奥氏体稳定性以及马氏体转变量。
5)  martensite [英]['mɑ:tən,zait]  [美]['mɑrtən,zaɪt]
马氏体
1.
Effect of deformation on the temper process of lath martensite;
形变对板条马氏体回火组织的影响
2.
Cold rolling deformation and recrystallization behavior of martensite Ni_(40.5)Co_(32.5)Al_(27) alloy;
Ni_(40.5)Co_(32.5)Al_(27)马氏体合金的冷变形和再结晶行为
3.
Influence of heat treatment on the properties of the heat-resistance martensite stainless steel 0Cr_(17)Ni_4Cu_4Nb;
热处理对耐热马氏体不锈钢0Cr_(17)Ni_4Cu_4Nb性能的影响
6)  martensitic steel
马氏体钢
1.
The microstructure and mechanical properties of China low activation martensitic steel;
低活化马氏体钢的微观结构与力学性能
2.
Introduces forging technology and matters needing attention of valve of martensitic steel 4Cr 10 Si 2Mo, analyses the reason that the steel can ’t be cooled by air, compares forging characteristics with valve of austenitic steel 4Cr 14 Ni 14 W 2Mo and come to the feasiblity of new technology of valve adopting direct extrusion.
介绍了马氏体钢4Cr10Si2Mo气阀的锻造工艺及生产中的注意事项,分析了这种钢不能采用空冷的原因,并且与奥氏体钢4Cr14Ni14W2Mo气阀的锻造特点进行了比较,提出了气阀生产新工艺———正挤压的可行性。
3.
n this research, the characteristic of martensitic steel in abrasion was investigated by using three different test methods.
98%4种合碳量马氏体钢的磨料磨损特性进行了考察。
补充资料:体量
1.禀性。 2.气量;器度。 3.指建筑物的规模。 4.犹体谅。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条