1) radial extrusion
径向挤压
1.
Technical Study of Radial Extrusion Forming on the Super-Long Odd Shafts based on Multiple Directions Extrusion
基于多向挤压的超长异形轴径向挤压工艺研究
2.
The radial extrusion technological process of the internal thread spline was studied and a set of extrusion mould suitable for the forming of the internal thread spline in the guide bush.
以汽车单向器导向筒内螺旋花键为研制对象 ,对内螺旋花键的径向挤压工艺进行了研究 ,设计了1副适合于导向筒内螺旋花键径向成形的挤压模。
3.
The warm radial extrusion of internal ring with inclined groove is introduced in this paper.
介绍了斜槽内环零件的温径向挤压工艺及三瓣模的设计、模具结构及主要零件的设计及选材。
2) bearing stress/radial continous extrusion
挤压应力/径向连续挤压
3) compressing lateral extrusion
扩径侧向挤压
1.
According to the moving direction relations between punch and workpiece,a new definition of lateral extrusion has been put forward,at the same time,the new concepts of compressing lateral extrusion,equal-cross section lateral extrusion and stretching lateral extrusion have been put forward too.
根据挤压方向和挤出方向之间的相互关系,对侧向挤压这一概念赋予了新的定义,同时也提出了扩径侧向挤压、等径侧向挤压和缩径侧向挤压3个新概念,进一步给出了等径侧向挤压真应变的计算公式,并指出等径侧向挤压法是制备块状细晶材料的一种好方法。
4) equal-cross section lateral extrusion
等径侧向挤压
1.
According to the moving direction relations between punch and workpiece,a new definition of lateral extrusion has been put forward,at the same time,the new concepts of compressing lateral extrusion,equal-cross section lateral extrusion and stretching lateral extrusion have been put forward too.
根据挤压方向和挤出方向之间的相互关系,对侧向挤压这一概念赋予了新的定义,同时也提出了扩径侧向挤压、等径侧向挤压和缩径侧向挤压3个新概念,进一步给出了等径侧向挤压真应变的计算公式,并指出等径侧向挤压法是制备块状细晶材料的一种好方法。
2.
In this paper,the strain of the equal-cross section lateral extrusion has been analyzed,and the true strain and equivalent true strain formulae are derived from the strain analysis of the plane-pureshear deformation.
对等径侧向挤压变形的应变进行了深入的分析，应用平面纯剪切变形应变分析的结果，得到了等径侧向挤压变形真应变和等效真应变的计算公式，分析了循环等径s型侧向挤压真应变和等效真应变的变化规律。
5) stretching lateral extrusion
缩径侧向挤压
1.
According to the moving direction relations between punch and workpiece,a new definition of lateral extrusion has been put forward,at the same time,the new concepts of compressing lateral extrusion,equal-cross section lateral extrusion and stretching lateral extrusion have been put forward too.
根据挤压方向和挤出方向之间的相互关系,对侧向挤压这一概念赋予了新的定义,同时也提出了扩径侧向挤压、等径侧向挤压和缩径侧向挤压3个新概念,进一步给出了等径侧向挤压真应变的计算公式,并指出等径侧向挤压法是制备块状细晶材料的一种好方法。
6) equal-channel angular pressing (ECAP)
侧向等径挤压(ECAP)
补充资料：冲击挤压(见冷挤压)
冲击挤压(见冷挤压)
impact extrusion
ehongji jiya冲击挤压(impaet extrusion)见冷挤压。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条