1) waste polyolefin
废聚烯烃
1.
Progress in catalytic pyrolysis of waste polyolefins;
废聚烯烃催化裂解研究进展
2) waste PO film
聚烯烃废膜
1.
The plashcizing and extruding system with both drainning water and venting was developed for recycling waste PO film.
介绍了笔者研制的排水排气式聚烯烃废膜回收塑化挤压系统的结构特征，及该系统所采用的回收工艺。
3) waste polyolefins
聚烯烃类废塑料
1.
The catalytic degradation of waste polyolefins and recovery of fuel oil were studied when applied various catalysts,the pyrolysis mechanism of waste polyolefins was investigated.
研究使用不同催化剂情况下聚烯烃类废塑料热分解回收燃油的技术，并对废塑料的热分解机理进行了探讨。
4) polyolefin
[,pɔli'əuləfin]
聚烯烃
1.
Actuality and Prospect of Research and Development of Foaming Master Batch of Polyolefin;
聚烯烃发泡母粒的研制及生产现状与展望
2.
Current Situation and Developing Tendency of Flame Retardant Polyolefin;
聚烯烃阻燃技术研究现状及进展
3.
Advances and development proposal in single-site catalyst of polyolefin;
聚烯烃单活性中心催化剂研究进展及发展建议
5) poly-α-olefin
聚α-烯烃
1.
The market demand of poly-α-olefin(PAO) in synthetic oils was one of the fastest growing,the PAO synthetic lubricants not only have the advantage of lower volatility,higher viscosity index,lower pour point,higher flash point and excellent high temperature anti-oxidation performance,but also have long use life compared with mineral oils.
合成油中聚α-烯烃(PAO)是市场需求增长最快的品种之一。
2.
As the regulation of lubricants is becoming more and more strict, demand of high quality lubricating oils is increasing, among which most distinctly is synthetic oil, especially poly-α-olefin synthetic oil.
合成油中的聚α-烯烃(PAO)是市场需求增长最快的品种之一。
3.
By employing orthogonal design L9(33),effects of polymerization temperature,catalyst quantity and reaction time on the conversion of olefins and the viscosity of poly-α-olefin lubricating base oil were studied.
以焦化汽油馏分为原料,采用碳正离子聚合的方法直接聚合聚α-烯烃合成润滑油基础油。
6) Olefin polymerization
烯烃聚合
1.
Recent progress in the immobilization of non-metallocene olefin polymerization catalyst;
非茂金属烯烃聚合催化剂的载体化研究进展
2.
Characterization techniques for the morphology of supported catalyst and nascent polymer particles in olefin polymerization;
烯烃聚合中负载型催化剂及初生聚合物颗粒形貌的表征评述
3.
Study on the Chain initiation for Olefin Polymerization with Neutral Salicylaldiminato Nickel(II) Catalyst by Density Functional Theory;
中性水杨醛亚胺镍催化烯烃聚合反应链引发机理的密度泛函研究
补充资料：聚丁烯/聚烯烃共混物
分子式：
CAS号：
性质：聚丁烯具有良好的机械性能，突出的是耐环境应力开裂性、耐低温流动性和耐蠕变性；耐热性、耐化学药品性良好，具有抗磨性、可挠曲性和高填料填充性。将聚丁烯与HDPE共混可改善其加工性能，如与PP共混则可提高其冲击强度。这类共混物一般采用机械共混法制备。
CAS号：
性质：聚丁烯具有良好的机械性能，突出的是耐环境应力开裂性、耐低温流动性和耐蠕变性；耐热性、耐化学药品性良好，具有抗磨性、可挠曲性和高填料填充性。将聚丁烯与HDPE共混可改善其加工性能，如与PP共混则可提高其冲击强度。这类共混物一般采用机械共混法制备。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条