1) Potentiodynamic scan using three electrodes
三电极动电位扫描
2) potentiodynamic polarization
动电位扫描
1.
The corrosion behaviors of such alloy were measured through salt spray test and potentiodynamic polarization test.
采用盐雾腐蚀和动电位扫描研究了稀土元素Ce、Nd对AZ31镁合金耐腐蚀性能的影响。
2.
Electrochemical characteristics of carbon steel in CO\-2\|saturated 3mol/L MEA, DEA and ABT solutions were investigated using electrochemical methods such as potentiodynamic polarization, impedance measurement and open-circuit relaxation potential curve under 80℃ and 0.
采用动电位扫描法、电化学阻抗等电化学方法 ,研究了在 80℃ ,0 。
3) dynamic potential scanning
动电位扫描
1.
The results are compared with the dynamic potential scanning results in the weak polarization condition.
利用恒电量仪测定了钢筋混凝土中水灰比及二级粉煤灰含量对钢筋 (45 #钢 )的腐蚀行为的影响 ,并用恒电位仪的弱极化动电位扫描曲线解析结果与之比较 。
2.
The over potential of the stainless steels 1Cr18Ni9Ti and Cr17Ni2 were measured by dynamic potential scanning method in electrode without immersion way and electrode immersion way.
采用微生物学方法研究了SRB在不同生长时期的形貌,采用动电位扫描法研究了在非浸泡试验方式和浸泡试验方式下1Cr18Ni9Ti和Cr17Ni2电极过电位随时间的变化规律。
4) potentiodynamic scanning
动电位扫描
1.
The electrode process kinetics of chlorine evolution and copper electrolytic deposition on the electrode surface has been investigated by the steady-state potentiodynamic scanning and cyclic voltammetry.
在印刷电路板酸性蚀刻废液中选用Ir系和Ru系电极作阳极,通过稳态动电位扫描和循环伏安扫描,对电极表面发生析氯和电积铜反应过程动力学进行了研究。
5) anodic linear potential sweep
阳极动电位扫描法
1.
The effect exerted by H 2S on the corrosion behavior of N80 # oil pipe steel in given pH value but various C H 2S and given C H 2S but various pH value solutions was studied by means of stable polarization and anodic linear potential sweep.
用稳态极化法 ,阳极动电位扫描法研究了给定酸度而不同H2 S浓度和给定H2 S浓度而不同酸度的溶液中H2 S对N80号油管钢腐蚀行为的影响 。
6) scan electrode
扫描电极
1.
On the basis of the analysis of high voltage driving waveforms and the consideration of the driving circuit design of scan electrode, the design method of the high voltage driving circuit of scan eletrode, and the energy recovery circuit are studied.
介绍了PDP驱动电路的构成,在分析扫描电极高压驱动波形和驱动电路设计考虑的基础上,研究了扫描电极高压驱动电路的实现方法,并对能量恢复电路作了一定的介绍。
2.
In this paper,we introduce the advantages of ALIS driving method,and the design of the driving circuit of scan electrode;Using MAX+plusⅡsoftware,the driving waveform of scan electrode was realized through combining Text editor with Graphic editor.
介绍了表面交替发光(ALIS)驱动方法的原理;介绍了扫描电极驱动电路硬件的设计及实现方法;利用MAX+plusⅡ软件,结合原理图和VHDL语言设计了驱动要求的驱动波形。
补充资料：电极电位
分子式：
CAS号：
性质：又称电极势，电极电位，电池单极电势或半电池电动势。构成电极的金属(或非金属)与溶液之间因发生电化学反应而产生的相间电势差。单个电极电势的绝对值迄今无法直接测定。以标准氢电极的相对平衡电势为零作参考点，得到氢的标准电极电势。将电极和标准氢电极组成电池，所测得的电池电动势即为该电极的电极电势。电极电势是反映电极反应趋势的参数，也是判定氧化还原反应能否进行的依据。
CAS号：
性质：又称电极势，电极电位，电池单极电势或半电池电动势。构成电极的金属(或非金属)与溶液之间因发生电化学反应而产生的相间电势差。单个电极电势的绝对值迄今无法直接测定。以标准氢电极的相对平衡电势为零作参考点，得到氢的标准电极电势。将电极和标准氢电极组成电池，所测得的电池电动势即为该电极的电极电势。电极电势是反映电极反应趋势的参数，也是判定氧化还原反应能否进行的依据。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条