说明：双击或选中下面任意单词，将显示该词的音标、读音、翻译等；选中中文或多个词，将显示翻译。
您的位置：首页 -> 词典 -> 渐升式温度曲线
1)  Ramp profile
渐升式温度曲线
2)  elevated temperature curve
升温曲线
1.
The influence of elevated temperature curve and the location of fire of on the rise of temperature of the tapered beam is studied.
采用有限元法对门式钢刚架结构中的变截面梁进行了数值模拟,分别得到其在ISO标准升温曲线和局部火灾下的温度场变化,考察了升温曲线及火源位置对变截面梁升温的影响。
2.
In this thesis, behaviors of unbonded prestressed concrete slabs including 4 simply-supported slabs and 9 continuous slabs are investigated under fire, based on the elevated temperature curve accord to the ISO standard fire curve.
本文采用标准升温曲线，对4块简支板及9块连续板分别进行了火灾行为的试验研究。
更多例句>>
3)  curve of temperature increasing
温升曲线
1.
By the method of lowest two multiplications, the ideal curve of temperature increasing of EED can be obtained, which serves as a ground of nondestructive inspection and effectively evaluates the explosion properties of EED.
用最小二乘法拟合电雷管点火头的理想温升曲线作为无损检测的判据,从而有效地判断电雷管的爆炸性能。
4)  the curve of rised and lowered temperature
升降温曲线
1.
Based on heat balace differential equation, a new formula for deducing the curve of rised and lowered temperature is developed under a certain fix power.
以电热法养护热平衡微分方程式为基础，确定了在固定功率条件下升降温曲线的计算公式。
5)  Temperature profile
温度曲线
1.
The article introduces the general technology requirements for reflow soldering and typical temperature profile and techni- cal parameter of the main control point at the temperature profile, and also describes common quality defects of reflow soldering, briefly discusses the reasons of production defects and appropriate countermeasure.
文中介绍了再流焊的一般技术要求,并给出了典型温度曲线以及温度曲线上主要控制点的工艺参数。
更多例句>>
6)  temperature curve
温度曲线
1.
Design of heating device for magnesium alloy isothermal forging and temperature curve of die;
镁合金等温锻造加热装置的设计及模具温度曲线
2.
Study on the temperature curve in semen freezing of the small-tail sheep;
小尾寒羊精液冷冻温度曲线初步研究
3.
The influence of SMT reflow soldering temperature curve on the welding quality
SMT再流焊温度曲线对焊接质量的影响
更多例句>>
补充资料：渐屈线(平面曲线的)


渐屈线(平面曲线的)
evohite (of a pbne curve)

渐屈线(平面曲线的)【e，浦血何a内I此。口，e);”。几犯-Ta.月oc，0.鱿P二o面」 已知曲线7的曲率中心的集合下.若r二r(s)(其中、是7的弧长参数)是7的方程，则它的渐屈线的方程有如下形状: *r+去，，其中k是曲率而，是下的单位法向量.下图显示了三种典型情形下渐屈线的构造: a)若沿整条曲线k’有固定符号且k不为零;今赚条‘b S0 图c b)若沿整条曲线k’有固定符号且k在s=s。处为零; e)若对于s0;对于s>50，k‘<0:k‘(50)二0，并且k不为零(渐屈线上对应于s“s。的点是尖点). 与下的曲线段sl簇s毛s:对应的渐屈线的弧长是 ‘(S，一)一}共一共}. 】火气52)凡气s，)1渐屈线是下的法线族的包络.曲线7称为它的渐屈线的渐伸线(见渐伸线(平面曲线的)(e明习硫mt(ofap】anec山、吧))).八.八.Cb盆o月o“撰【补注】若犷是下的渐屈线，则下是丫的渐伸线，见渐伸线(平面曲线的)(e铂1卿t(of aP妞叱c透ve)).
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条