1) ketosulfone
酮砜
1.
The asymmetric reduction of ketosulfone with borane catalyzed by oxazaborolidine is computed by means of the semi-empirical MNDO method.
对噁唑硼烷催化前手性酮砜不对称还原反应进行了半经验MNDO研究。
2) PPESK
聚醚砜酮
1.
Mechanical properties of continuous carbon fiber reinforced PPESK blends composites;
连续炭纤维增强杂萘联苯聚醚砜酮共混树脂基复合材料力学性能
2.
Preparation of PPESK based composite carbon membrane for gas separation
聚醚砜酮基炭膜的制备及其气体分离性能
3.
Nanometer and micrometer ZrO2 particle-filled poly (phthalazine ether sulfone ketone) (PPESK) composites with various filler volume fractions were prepared by heating compression molding.
采用热压成型的方法制备了纳米、微米ZrO2填充聚醚砜酮(PPESK)复合材料;考察了复合材料的显微硬度和弯曲强度;并研究了干摩擦条件下纳米、微米ZrO2颗粒对复合材料摩擦磨损性能的影响;利用扫描电子显微镜(SEM)观察分析ZrO2/PPESK复合材料磨损表面形貌及磨损机理。
3) poly(phthalazine ether sulfone ketone)
聚醚砜酮
1.
Structure and performance of PEG-acrylate immobilized porous poly(phthalazine ether sulfone ketone) membrane;
聚乙二醇丙烯酸酯表面改性聚醚砜酮微孔膜的结构和性能
2.
The dry sliding friction and wear properties of nanometer TiO 2 particle filled poly(phthalazine ether sulfone ketone) (PPESK) composites were investigated with an MM 2000 tester by sliding PPESK based composites against plain carbon steel(AISI1045) ring, with an emphasis on exploring the effect of the filler content and applied loads on the tribological behaviors of the composites.
采用热压成型的方法制备了纳米 Ti O2 填充聚醚砜酮 (PPESK)复合材料 ,在 MM- 2 0 0 0摩擦磨损试验机上考察了干摩擦条件下纳米 Ti O2 含量以及试验载荷对复合材料摩擦磨损性能的影响 ,并利用扫描电子显微镜 (SEM)观察分析 PPESK及纳米 Ti O2 / PPESK复合材料磨损表面形貌及磨损机理。
4) sulfone/ketone ratio
砜酮比
1.
The results showed that glass transition temperature (T g) of the fiber increased along with sulfone/ketone ratio.
采用DSC、TG测定了含联苯结构聚芳醚砜酮 (PPESK)纤维的热性能 ,结果表明 ,纤维的玻璃化温度随砜酮比的增大而提高 ,纤维的起始分解温度大于 463℃。
5) PPESUK
聚醚砜酮
1.
INFLUENCES OF THE LOAD, VELOCITY AND TEMPERATURE ON THE FRICTION AND WEAR PROPERTIES OF PPESUK;
载荷、速度及环境温度对聚醚砜酮摩擦磨损性能的影响
2.
Nanometer and micrometer ZnO particle-filled PPESUK composites with various filler volume fractions were prepared by heating compression molding.
用热压成型法制备了纳米、微米ZnO填充联苯型聚醚砜酮(PPESUK)复合材料;考察了复合材料的显微硬度和弯曲强度;并研究了干摩擦条件下纳米、微米ZnO对复合材料摩擦磨损性能的影响。
6) β ketosulfone
β-酮砜
补充资料：2-(2-氯-4-甲砜基)苯甲酰基-1,3-环己二酮
分子式：C14H13ClO5S
分子量：328.77
CAS号：99105-77-8
性质：
分子量：328.77
CAS号：99105-77-8
性质：
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条