说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 差速器
1)  Differential [英][,dɪfə'renʃl]  [美]['dɪfə'rɛnʃəl]
差速器
1.
Application and Analysis of the Differentials of LHD Units;
铲运机差速器应用与分析
2.
Movement Analysis of Different Screw-pitch Axial Sliders Cam Differential;
不同螺距轴向滑块凸轮式差速器的仿真分析
3.
Improvement on Axle Construction of Differential Planet Gear;
差速器行星齿轮轴结构的改进
2)  differential mechanism
差速器
1.
By analyzing the working principle of the anti-slipping differential mechanism on the carry scraper,this paper discusses the influence of two sorts of differential mechanism to the vehicle capability on typical conditions.
重点对井下铲运机防滑差速器的工作原理进行分析,然后就两种差速器在铲运机的几种典型工况下对整机驱动性能的影响进行计算分析。
2.
The paper introduces the fuzzy optimum design method on differential mechanism of handling machinery.
介绍了起重运输机械起升机构差速器的模糊优化设计方法 。
3.
power,angular velocity structure parameter of the 2KH differential mechanism used in changing diameter rell transmission.
文中应用差动比概念,从运动分解及功率分流着手,对变直径卷辊传动用2KH差速器的转矩、功率、角速度及结构参数选择作了深入探讨,提出了降低速度波动幅度及张力波动幅度,提高传动平稳性的技术措施,为开发该类产品提供了可靠的理论依据。
3)  differential gear
差速器
1.
This paper presents the dynamic simulation on vehicle axle s differential mechanism based on UG/Scenario for Motion, in which motion characteristics for the components are found Therefore, the mechanism for differential gears is proved.
介绍应用UG软件对车桥差速器进行运动仿真,并求得各构件的运动特性,验证了差速器的差速原理。
2.
This paper studies the improved design to reduce the wearing of tires under the circumstances of different travelling conditions of wheels by means of using a differential gear on the driving bridge of combination car to separate the right and left wheels.
研究了在正三轮摩托车的驱动桥中用差速器将其左右轮隔开,使车轮在行驶条件不一致的情况下减少磨损的改进设
4)  differential carrier
差速器壳
1.
,in sand casting process of differential carrier,lost pattern casting was employed to produce differential carrier.
为解决汽车差速器壳砂型铸造中存在的飞边毛刺多、偏芯、缩松等缺陷,采用了消失模铸造法生产差速器壳。
2.
The vertical molding process in Disa-molding line to produce the differential carrier casting with ductile iron is developed.
我厂为某公司在DISA线(垂直分型造型线)上开发的差速器壳球铁铸件的铸造生产工艺,采取了无冒口工艺、设冷却片、控制铁水高碳含量、低温快浇、封闭式浇注系统等措施,有效地降低了缩孔(缩松)倾向及其它铸造缺陷。
5)  differential lock
差速器锁
6)  differential compartment
差速器室
补充资料:ABD-自动制动差速器
ABD-自动制动差速器

是制动力系统的一个新产品,它的主要作用是缩短制动距离,和ABS、EBD等配合适用。当紧急制动时,车会向下点头,车的重量前移,而相应的车的后轮所承担的重量就会减少,严重时可以使后轮失去抓地力,这时相当于只有前轮在制动,会造成制动距离过长。而ABD可以有效防止这种情况,它可以通过检测全部车轮的转速发现这一情况,相应的减少后轮制动力,以使其与地面保持有效的摩擦力,同时将前轮制动力加至最大,以达到缩短制动距离的目的。ABD与ABS的区别在于,ABS是保证在紧急制动时车轮不被抱死,以达到安全操控的目的,并不能有效的缩短制动距离。而ABD则是通过EBD在保证车辆不发生侧滑的情况下,允许将制动力加至最大,以有效的缩短制动距离。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条