2) cure kinetics
固化动力学
1.
Effect of carbon fibers surface characteristics on the cure kinetics of benzoxazine;
碳纤维表面对苯并噁嗪树脂固化动力学的影响
2.
The cure kinetics and mechanisms of 4,4'-diamiodiphenyl methane(TGDDM) epoxy/4,4'-diaminodiphenyl sulfone(DDS) modified with various composition of polysulfone nanofibers are studied using differential scanning calorimetry.
本文采用等温DSC研究不同用量纳米聚砜纤维对增韧4,4’-二氨基二苯甲烷四缩水甘油胺环氧树脂(TGDDM)/4,4’-二氨基二苯砜(DDS)体系固化动力学的影响。
3.
From the experimental data, it was found that the autocatalytic cure kinetic modeling correctly represented the cure kinetics of this system.
试验结果表明,该环氧树脂体系的固化动力学符合自催化固化反应模型。
3) cure kinetic
固化动力学
1.
The cure kinetics of bismaleimides(BMI) resin system was investigated by dynamic DSC analysis and the phenomenological model was established.
采用全动态DSC研究了双马来酰亚胺树脂(BMI)体系的固化反应动力学,建立了固化动力学的唯象模型。
2.
The cure kinetics of a bicomponent high performance epoxy resin was studied by dynamic DSC analysis,and the parameters of the cure reaction were obtained to establish a phenomenological model.
用全动态DSC研究了先进复合材料用高性能双组份环氧树脂的固化反应动力学,获得了固化反应的动力学参数,并建立了固化动力学的唯象模型。
3.
Differential scanning calorimetry (DSC) in dynamic and isothermal modes performs an analysis of the cure kinetics of a modified BMI system.
用差示扫描量热法 (DSC)研究了二烯丙基双酚A (DABPA)改性的二苯甲烷双马来酰亚胺 (BMIM)的固化动力学 。
4) curing kinetics
固化动力学
1.
Study on curing kinetics of novolac epoxy/bisphenol A cyanate resin system;
酚醛型环氧树脂/双酚A型氰酸酯树脂体系固化动力学的研究
2.
Study on curing kinetics for phenolic resins;
酚醛树脂固化动力学研究
3.
Study of curing kinetics of TDE-85/TH PA system by Differential Scanning Calorimetry (DSC);
采用差示扫描量热法(DSC)对TDE-85／70#酸酐体系固化动力学的研究
5) curing kinetic
固化动力学
1.
The curing action of 4,4′-methylene bis(2-chloroaniline) MOCA/epoxy resin(EP) curing system was studied by IR,DSC,and then it′s curing kinetics was studied.
采用FT-IR、DSC等方法研究了亚甲基双邻氯苯胺(MOCA)/环氧树脂体系的固化行为,并对其固化动力学行为进行了研究。
6) Cure kinetics
固化反应动力学
1.
The cure kinetics of the epoxy resin(N,N,N',N'-tetraglycidyl-4,4,-diaminodiphenyl methane,TGDDM)and the novel curing agent(2,2,-bis(3-amino-4-hydroxyphenyl)hexafluoro propane,BAHPFP)were studied by means of differential scanning calorimetry(DSC).
采用差示扫描量热法(DSC)研究了N,N,N',N'-四缩水甘油基-4,4’-二氨基二苯甲烷(TGDDM)与新型含氟固化剂2,2,-双(3-氨基-4-羟基苯基)六氟丙烷(BAHPFP)的固化反应动力学。
2.
The cure kinetics of middle temperature curing 3234 epoxy resin system was studied under isothermal and dynamic curing conditions by Differential Scanning Calorimetry (DSC) technique.
采用差示扫描量热法(DSC)在等温和动态条件下对3234中温固化环氧树脂体系的固化反应动力学进行了研究,建立了固化反应动力学方程;并模拟实际固化温度历程,采用测定不同固化阶段样品残余反应热的方法对固化反应动力学方程进行了验证。
3.
Non-isothermal cure kinetics of differential scanning calorimeter(DSC) showed that 1% surfactant exerts acceleration effect on the cure reaction of the epoxy,while 10% surfactant hinders the cure reaction.
DSC非等温固化反应动力学研究表明,1%(质量分数,下同)的表面活性剂对固化反应有促进作用,但10%的表面活性剂抑制了固化反应。
补充资料：动力机械：内燃机动力学
研究内燃机运转中的力学现象的科学。其主要任务是研究分析内燃机运转时各主要零件的运动规律及其受力情况﹐用以作为内燃机零件设计﹑计算的依据。它还研究这些力对内燃机动力装置的影响及其消减方法。内燃机动力学的主要内容为曲柄连杆机构运动学﹑曲柄连杆机构动力学和内燃机平衡分析等。
曲柄连杆机构运动学 研究曲柄﹑连杆﹐尤其是活塞的运动规律。活塞作周期性往复运动时的位移
、速度
和加速度
可用下述各式近似求算
式中为曲轴转角﹔ 
为曲轴旋转角速度﹔
为曲柄半径﹔
为曲柄半径 与连杆长度
之比﹐即 ＝ /
曲柄作回转运动﹐连杆作复杂的平面运动。连杆的运动往往被简化分解为随活塞组的往复运动和随同曲柄的旋转运动。
曲柄连杆机构动力学 研究分析曲柄连杆机构(见曲柄滑块机构)在运动中力的生成﹑传递和输出。作用在曲柄连杆机构上的力有曲柄连杆机构运动时产生的往复惯性力和离心惯性力﹐以及内燃机气缸内的气体压力。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条