1) mixing time
混料时间
1.
Influence of mixing time on characteristics of aircraft friction materials;
混料时间对航空刹车摩擦材料性能的影响
2) mixing time
混料时间<发泡>
3) mixing time
混匀时间
1.
Water model study on mixing time in a 210 t ladle in the CAS process;
210t钢包CAS精炼混匀时间的水模型试验研究
2.
The experimental study on the influences of adding position of tracking agent,arrangement mode of gas supply bricks and different quantities of gas supply on mixing time of molten steel was performed via water model.
采用水力学模型实验方法研究了不同示踪剂加入位置、不同透气砖布置方式以及不同送气量对钢液混匀时间的影响。
3.
A water model for 130t ladle has been established and the mixing time of the molten steel in the ladle measured by conductivity method.
以130t钢包为研究对象建立水力学模型,以电导法测定了底吹氩钢包内钢液的混匀时间,讨论钢包底吹氩工艺中透气元件不同布置方式以及不同吹气量对钢液混匀时间的影响。
4) Mixing Time
均混时间
1.
Water modeling of mixing time of CAS-OB bath with powder injection;
CAS-OB喷粉精炼熔池内均混时间的水模研究
2.
A Study of Water Modelling on Mixing Time for a 300 t Hot Metal Desulphurization-Pretreated by Double-Lance Injection Process
300t铁水包双枪喷吹脱硫均混时间的水模型研究
3.
The circulation flow rate,mixing time,mean residence time,volumetric mass transfer coefficient of the RH refining process were determined by water modeling.
通过物理模拟测定了RH精炼过程的循环流量、钢包的均混时间、真空室内物料的平均停留时间及容量传质系数,重点分析了RH上升管内的提升气体用喷嘴个数及其布置对上述4个方面特性的影响。
5) uniform mixing time
均混时间
1.
The study of uniform mixing time for bubble refinement;
气泡微细化实验中均混时间的研究
2.
Based on the experiment data of hot metal pretreatment by powder injecting in water model,the influences of handling parameters on transport dynamic basic parameters (uniform mixing time,powder penetration ratio,residence time of powder) and the definite function form of transport dynamic basic parameters were gotten by linear regression.
在鱼罐喷粉预处理水模实验数据的基础上 ,进一步利用线性回归确定各工艺操作参数对喷吹基本参数 (均混时间、粉剂穿透比和粉剂停留时间 )的影响 ,得出各传输动力学基本参数的函数关系
3.
The uniform mixing time of the bath and the penetration ratio of injected powder into the melt are the basic transport dynamic parameters of hot metal dephosphorization pretreatment by powder injection in torpedo.
溶池均混时间和粉剂穿透比是鱼雷罐喷粉预处理研究中基本的传输动力学参数 通过水模实验 ,测定了不同熔池深度、不同喷枪插入深度和角度以及不同喷枪平面位置条件下吹气对熔池搅拌的影响 实验研究和分析了影响粉剂穿透比的因素 ,得出了本实验条件下粉剂理论穿透比与粉剂临界穿透直径之间的关系
6) reverberation time
混响时间
1.
Technique of adjustable reverberation time in auditorium
观众厅可调混响时间技术
2.
Research on optimal reverberation time in classrooms
教室室内最佳混响时间的研究
3.
The reverberation time and noise level of tunnel-typed public works can be reduced by adding large amount of acoustical structure with high absorptive coefficient.
隧道型公共设施的声环境,可以使用大量具有高吸声系数的吸声构造,铺设于隧道拱壁及轨道铺面,以降低混响时间及噪声。
补充资料：预混料
分子式：
CAS号：
性质：指橡胶与聚乙烯等塑料，或与再生胶、纤维等需要单独塑化、精炼，而预先制成的母料。
CAS号：
性质：指橡胶与聚乙烯等塑料，或与再生胶、纤维等需要单独塑化、精炼，而预先制成的母料。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条