1) 304 austenitic stainless steel
304奥氏体不锈钢
1.
The influences of deformation rate on the mechanical properties of 304 austenitic stainless steel were studied by tensile test at room temperature.
采用室温拉伸实验研究了不同变形速度对304奥氏体不锈钢力学性能的影响规律。
2.
Solid Solution Nitriding of 304 Austenitic stainless steel and 3Cr13 Martensite stainless steel was investigated under the following technical parameters: temperature 900℃~1150℃,nitrogen pressure 0.
本文对304奥氏体不锈钢和3Cr13马氏体不锈钢的固溶渗氮进行了研究,固溶渗氮工艺参数的变化范围为:渗氮温度900℃～1150℃,氮气压力0。
3.
In this paper investigated the deep-drawing process of 304 austenitic stainless steel sheet and the friction and lubrication in the deforming process of the shell of permissible respirator self rescue from carbon monoxide.
本文研究了304奥氏体不锈钢自救器筒体制造工艺中的拉深工艺及摩擦润滑情况。
2) 304 Austenite Stainless Steel
304奥氏体不锈钢
1.
Effect of Cu on Strain-Induced Martensite Transformation in 304 Austenite Stainless Steel;
Cu对304奥氏体不锈钢应变诱发马氏体相变的影响
2.
Starting from lubricating status and drawing speed, the reasons of sticky lump caused by 304 austenite stainless steel drawing are analyzed, combining with actual situation of cooperating partner of the project, improving steps are provided, and proper lubricant is carried out.
从润滑状态及拉伸速度入手,分析了304奥氏体不锈钢拉伸时粘结瘤形成原因,结合项目合作单位的实际情况提出了改进措施,配制了合适的润滑剂。
3.
In the present paper, the effects of processing conditions on the deep-drawing deformation of 304 austenite stainless steel sheet were investigated by means of physic simulation and numerical simulation.
本文采用物理模拟和数值模拟技术，研究了拉深工艺条件对304奥氏体不锈钢拉深成形过程的影响规律。
3) as-cast 304 austenitic stainless steel
铸态304奥氏体不锈钢
4) 304/316 austenitic stainless steel
奥氏体不锈钢304/316
5) AISI 304 austenitic stainless steel
AISI 304奥氏体不锈钢
1.
Glow discharge nitriding and nitrocarburising in AISI 304 austenitic stainless steel were approached in this paper.
本课题针对AISI 304奥氏体不锈钢进行辉光离子渗氮和离子氮碳共渗研究。
6) austenitic stainless steel
奥氏体不锈钢
1.
Research on intergranular atuack of Fe-17Mn-13Cr-0.3N austenitic stainless steel;
Fe-17Mn-13Cr-0.3N奥氏体不锈钢的晶间腐蚀研究
2.
Effect of Magnetic Field of the Pulse on the Quenched Structure of Austenitic Stainless Steel;
脉冲磁场对奥氏体不锈钢液淬组织的影响
3.
Chemical cleaning of austenitic stainless steel and passivation;
奥氏体不锈钢设备的化学清洗和钝化
补充资料：奥氏体不锈钢
分子式：
CAS号：
性质：在常温下具有奥氏体组织的不锈钢。含铬18%和镍8%的不锈钢是最典型的奥氏体不锈钢，它常被称为18-8不锈钢。这种不锈钢在很宽的温度范围内都具有很高的强韧性，富于延展性，容易轧制和压缩等冷加工，它的耐蚀性和耐酸性，都优于铁素体不锈钢和马氏体不锈钢。添加钼和铜的镍铬系奥氏体不锈钢具有更好的耐蚀性和耐酸性，而且耐盐酸和卤化物腐蚀性也大为改善。除铬镍系奥氏体不锈钢之外，还有铬镍锰系以及不含镍和铬的铁锰铝系奥氏体不锈钢。由于奥氏体不锈钢具有全面、良好的综合性能，在工业上获得了广泛应用。
CAS号：
性质：在常温下具有奥氏体组织的不锈钢。含铬18%和镍8%的不锈钢是最典型的奥氏体不锈钢，它常被称为18-8不锈钢。这种不锈钢在很宽的温度范围内都具有很高的强韧性，富于延展性，容易轧制和压缩等冷加工，它的耐蚀性和耐酸性，都优于铁素体不锈钢和马氏体不锈钢。添加钼和铜的镍铬系奥氏体不锈钢具有更好的耐蚀性和耐酸性，而且耐盐酸和卤化物腐蚀性也大为改善。除铬镍系奥氏体不锈钢之外，还有铬镍锰系以及不含镍和铬的铁锰铝系奥氏体不锈钢。由于奥氏体不锈钢具有全面、良好的综合性能，在工业上获得了广泛应用。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条