说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 使用性
1)  serviceability [,sə:visə'biliti]
使用性
1.
The causes of weld overlay cracking on hydroprocessing reactors and the effect on serviceability were analyzed in this paper.
由于壳体基材有高的断裂韧性,堆焊层裂纹不会扩展到壳体基材,堆焊层裂纹不影响加氢反应器的使用性
2.
The factors discussed address the restoration of serviceability and the correction of cosmetic defects and are not applicable to failures resulting from overloading.
本文讨论这些因素,致力于使用性的恢复和表面缺陷的修复,对于超载引起的损坏则不适用。
2)  service performance
使用性能
1.
Decision analysis of the surface quality based on service performance of the parts;
基于零件使用性能的表面质量决策分析
2.
Application of grey-Markov model to forecasting service performance of airport pavement
灰色-马尔科夫模型在机场道面使用性能预测中的应用
3.
Analysis on factors had influences on construction machinery service performance
影响工程机械使用性能的因素分析
3)  performance [英][pə'fɔ:məns]  [美][pɚ'fɔrməns]
使用性能
1.
The determination fundamentals of laser-diffraction granularity tester andits performance;
激光衍射粒度仪测量原理及使用性
2.
Study on Stone Arch Bridge Performance Assessment and Reinforcement Measures;
石拱桥使用性能综合评价与加固对策研究
3.
Markov probability forecasting of performance of asphalt pavement in expressway;
高速公路沥青路面使用性能马尔可夫概率预测
4)  using performance
使用性能
1.
Layout types of automotive ABS and the influence to using performance;
ABS的布置形式及其对使用性能的影响
2.
On the condition of temperature was 150、163、180 ℃ and aging time was 30 h,the transformative relationship on the composition of asphalt influences on using performance of asphalt was investingated.
在 150、163、180℃高温下, 30h的老化时间内,采用沥青 4组分(饱和组分、芳香组分、胶质和沥青质)分析法对彩色沥青老化时组成及使用性能的变化情况进行了测试实验。
3.
Running conditions closely related to the running safety of vehicles in forest areas and factors affecting using performance are analyzed and a battery of measures are put forward to ensure running safety in forest areas.
本文分析了与林区车辆行驶安全密切相关的运行条件及使用性能因素 ,并据此提出了确保林区行驶安全的一系列措
5)  Benign use
良性使用
6)  serviceability [,sə:visə'biliti]
使用性能
1.
The results obtained show that the hardness and adhesion strength of the adhesive coating layer are important characteristics It is useful to improve the serviceability of adhesive layer with reasonable curing parameters and controlling inner stres
对评定粘涂层质量的主要力学性能进行了研究 ,结果表明硬度和附着强度值为评定其使用性能的主要参数 合理选择固化工艺参数、抑制和调控粘涂层中的内应力有助于提高粘涂层的使用性
2.
In this paper the conception of road surface management system is elaborated, and the reasons caused pavement breakage are analyzed; at the same time the collection of the data on road position and the evaluation of serviceability are talked about, which can be taken as the reference of maintenance and management for highway department.
本文阐述了路面管理系统的概念,分析了路面破损原因,论述了路面管理系统中路况数据采集与使用性能评价,可供公路养护管理部门参考。
3.
It is proved that micro-surfacing is a method of perfect preventive maintenance performance, however it needs to be improved in some area of serviceability.
通过对沪宁高速公路实施微表处前后 ,路段使用性能的跟踪检测 ,研究分析了微表处在高速公路上的适用性和它对不同路面病害的工程实施效果。
补充资料:工具钢的使用性能及工艺性能
工具钢具有良好的强度、韧性、硬度、耐磨性和回火稳定性等性能。主要用于制造各种切削刀具、成形工具和测量工具。
(1) 硬度
 工具钢制成工具经热处理后具有足够高的硬度,如用于金属切削加工的工具一般在HRC60以上。工具在高的切削速度和加工硬材料所产生高温的受热条件下,仍能保持高的硬度和良好的红硬性。碳素工具钢和合金工具钢一般在180℃~250℃、高速工具钢在600℃左右的工作温度下,仍能保持较高的硬度。红硬性对热变形模具和高速切削刀具用钢是非常重要的性能。
(2) 耐磨性
 工具钢具有良好的耐磨性,即抵抗磨损的能力。工具在承受相当大的压力和摩擦力的条件下,仍能保持其形状和尺寸不变。
(3) 强度和韧性
 工具钢具有一定的强度和韧性,使工具在工作中能够承受负荷、冲击、震动和弯曲等复杂的应力,以保证工具的正常使用。
(4) 其他性能
 由于各种工具的工作条件不同,工具用钢还具有一些其他性能,如模具用钢还应具有一定的高温力学性能、热疲劳性、导热性和耐磨腐蚀性能等。
 工具钢除了具有上述使用性能外,还应具有良好的工艺性能。
(1) 加工性
 工具钢应具有良好的热压力加工性能和机械加工性能,才能保证工具的制造和使用。钢的加工性取决于化学成分、组织的质量。
(2) 淬火温度范围
 工具钢的淬火温度应足够宽,以减少过热的可能性。
(3) 淬硬性和淬透性
 淬硬性是钢在淬火后所能达到最高硬度的性能。淬硬性主要与钢的化学成分特别是碳含量有关,碳含量越高,则钢的淬硬性越高。
 淬透性表示钢在淬火后从表面到内部的硬度分布状况。淬透性的高低与钢的化学成分、纯洁度、晶粒度有关。
 根据用于制造不同的工具,对这两种性能各有一定的要求。
(4) 脱碳敏感性
 工具表面发生脱碳,将使表面层硬度降低,因此要求工钢的脱碳敏感性低。在相同的加条件下,钢的脱碳敏感性取决于其化学成分。
(5) 热处理变形性
 工具在热处理时,要求其尺寸和外形稳定。
(6) 耐削性
 对很制造刀具和量具用钢。要求具有良好的磨削性。钢的磨削性与其化学成分有关,特别是钒含量,如果钒质量分数不小于0.50%则磨削性变坏。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条