1) curing process parameter
固化过度
2) over-cured depth
过固化深度
1.
In order to increase the building accuracy of microstructure in stereolithography process in Z direction,the model of over-cured depth in stereolithography process is set up according to the characteristic of stereolithography process.
为提高快速成形系统堆积方向微细结构的制作精度,根据光固化激光快速成形工艺的成形特点,建立了光固化激光快速成形工艺过固化深度的理论模型,据此模型提出了通过减小激光功率与扫描速度之比、增大分层厚度以及增大激光束在液态与固态树脂中的投射深度比来减小过固化深度,并对以上结论进行了实验验证。
3) curing process
固化过程
1.
Study on the curing process of benzoxazine-epoxy copolymerization;
苯并口恶嗪/环氧树脂共聚固化过程研究
2.
The curing process of an epoxy-acrylics based photosensitive resin under a 514 nm Ar + laser beam and the initiation of a synergistic photo-initiator composed of a dye, a tertiary amine and an UV photo-initiator was studied.
研究了在 5 14 nm Ar+激光下丙烯酸环氧树脂在染料、叔胺、紫外引发剂协同引发下的固化过程。
3.
The structural changes in the curing process of bismaleimide resin were studied by means of FT-IR, which indicate that the curing reaction is in two steps.
利用傅里叶变换红外光谱法研究双马来酰亚胺树脂固化过程中的结构变化,认为双马来酰亚胺树脂固化反应分两步进行:第一步是低温下的“ENE”反应;第二步是高温下的Diels-Alder反应。
4) over-cured
过固化
1.
During the course of prototyping,there were additional cured area and over-cured phenomenon at the starting point of scanning path because of the asynchronism in response between workbench and light source.
在成形过程中,由于工作台响应与光源响应不同步,造成了在每层扫描起始位置存在多余的固化区域和过固化现象,层层累加,形成沿高度方向的突棱,影响了起始点处的尺寸精度;为了使光源和工作台的响应保持基本同步,通过理论计算和实验相结合的方法,采用对光开关指令进行延时30 ms的措施,避免了在扫描起始端形成多余固化区域和过固化,基本消除了突棱现象,保证了制件的尺寸精度。
5) Curing temperature
固化温度
1.
Influence of Curing Temperature on Performance of Epoxy Thermosets
固化温度对环氧树脂固化物性能的影响
2.
Effects of curing temperature and filler content on the performance of epoxy adhesive for restoration of cultural relic
固化温度及填料对文物环氧胶粘剂性能的影响
3.
The different curing temperature effect on the microstructures and properties of epoxy/rectorite nanocomposites were studied using X-ray diffraction (XRD) and dynamical mechanical analysis (DMA).
利用X衍射、动态力学分析(DMA)研究了不同的固化温度对环氧树脂/累托土纳米复合结构的性能及微结构的影响。
6) curing cycle
固化制度
1.
The curing cycle of polymeric composites has significant effect on its performance and economic indices.
聚合物基复合材料的固化制度是影响其性能经济指标的重要因素。
补充资料：阿弥陀三耶三佛萨楼佛檀过度人道经
【阿弥陀三耶三佛萨楼佛檀过度人道经】
（经名）佛说诸佛阿弥陀三耶三佛萨楼佛檀过度人道经，二卷，吴支谦译。与佛说无量寿经同本异译。外题略名佛说阿弥陀经，坊本表题曰：大阿弥陀经，三耶三佛萨楼佛檀为如来之尊号，过度是济度之义，此经说阿弥陀如来济度人道者。
（经名）佛说诸佛阿弥陀三耶三佛萨楼佛檀过度人道经，二卷，吴支谦译。与佛说无量寿经同本异译。外题略名佛说阿弥陀经，坊本表题曰：大阿弥陀经，三耶三佛萨楼佛檀为如来之尊号，过度是济度之义，此经说阿弥陀如来济度人道者。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条