1) centrifugal clear liquid
离心清液
1.
Through the analysis of water equilibrium system in alcohol production,the centrifugal clear liquid reflux mathematical model was established.
该数学模型可预测离心清液某物质浓度的变化,可根据生产实际确定最佳回配周期、排放周期,达到节水、节能,减少环境污染的目的。
2) fermentation centrifugal supernatant
发酵离心上清液
3) Centrifugal cleaning
离心清洗
1.
Centrifugal cleaning is an effective method for PCB cleaning.
离心清洗是清洗印制电路板的一种有效方法,它与传统的喷淋和超声等方法相比具有清洗能力强、对工件保护效果好和应用范围广等特点。
4) centrifugal liquid
离心液
1.
Losing fine cleaned coal is recovered by the study of fine cleaned coal treatment technology in centrifugal liquid,which would improve the cleaned coal yield and enterprise economic benefit.
通过对离心液末精煤处理工艺的研究,回收离心液中损失的末精煤,以提高精煤产率和企业经济效益。
5) mother liquid
离心母液
1.
To provide the basis for the treatment and discharge of wastewater,the spectrophotometry and high performance liquid chromatography were adopted to analyze the chemical composition in mother liquid of polyvinyl chloride by qualitative and quantificational methods.
采用分光光度法和高效液相色谱法对聚氯乙烯离心母液中化学成分进行定性和定量分析,结果表明,离心母液中双酚A含量较高,其对水样总有机碳的贡献率为52。
2.
In an experiment using EGSB reactor to treat low-mass concentration mother liquid of suspension polyvinyl chloride, the characteristics of anaerobic granular sludge as well as its influencing factors were emphatically studied and the surface of granular sludge was observed by scanning electron micrographs.
在EGSB反应器处理低质量浓度PVC离心母液废水的试验研究中,着重检测了反应器内颗粒污泥的性质及其活性影响因素,并用扫描电镜观测了颗粒污泥表面菌体分布情况。
3.
In the pilot study on the treatment of mother liquid of polyvinyl chloride produced by suspension polymerization (SPVC) by using a novel aerobic treatment system-4 cascade aerobic biofilm reactors with internal circulation, the removal efficiencies of the COD and turbidity at different HRT together with the resistance impact of the system were researched.
采用4级内循环式好氧生物膜反应器串联工艺对悬浮法聚氯乙烯(PVC)离心母液废水进行中试试验,研究了不同停留时间下系统对有机物和浊度的处理效果以及系统的抗冲击能力;观察了生物膜的生长和发展规律;对影响系统稳定运行的主要因素(悬浮物、摇蚊幼虫和营养物)进行了分析,并提出了相应的控制措施。
补充资料：降液管清液层高度
分子式：
CAS号：
性质：又称降液管清液层高度。板式塔降液管内的液柱液面到下层塔板的垂直距离。如图中的Hd（图暂缺）。为保持板式塔正常操作，避免发生液泛，降液管液柱高度不能超过一定限度。一般应满足Hd≤(0.4～0.6)(HT+hw)，式中HT为塔板间距，hw为堰高，系数一般取0.5，易起泡物系取0.4，不易起泡物系取0.6。
CAS号：
性质：又称降液管清液层高度。板式塔降液管内的液柱液面到下层塔板的垂直距离。如图中的Hd（图暂缺）。为保持板式塔正常操作，避免发生液泛，降液管液柱高度不能超过一定限度。一般应满足Hd≤(0.4～0.6)(HT+hw)，式中HT为塔板间距，hw为堰高，系数一般取0.5，易起泡物系取0.4，不易起泡物系取0.6。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条