1) TiAlN coating technology
TiAlN涂层技术
2) TiAlN coating
TiAlN涂层
1.
Thermal residual stress analysis of TiAlN coating;
TiAlN涂层的热残余应力分析
2.
Study on wear behavior of TiAlN coating on GDL-4 high speed steel;
GDL-4高速钢表面TiAlN涂层磨损性能研究
3.
TiAlN coating and TiN coating were deposited by the multi-arc ion plating on LY12 aluminum alloy which is used for tank-engine compressor blades.
用多弧离子镀技术,在坦克压气机叶轮材料LY12铝合金基体上沉积TiN涂层和TiAlN涂层。
3) TiAlN coatings
TiAlN涂层
1.
As a kind of ternary nanocomposite thin hard coatings,TiAlN thin hard coatings showed super mechanical properties than TiN coatings,for instance,the hardness of TiAlN coatings can reach 47GPa,much higher than that of TiN coatings;and TiAlN coatings are thermally stable until 700℃,but TiN coatings are oxidation at 500℃.
TiAlN涂层还具有抗磨损,摩擦系数小,热膨胀系数及热传导系数低等特性,这些特性与涂层中Al含量的多少有关,Al含量的改变会导致涂层微观结构的改变,从而使其性能发生变化。
2.
In this paper, The multi-component TiAlN coatings were deposited on WC-6%Co carbide and high-speed steel (HSS) respectively using reactive direct current(D.
用TiAlN涂层刀具和未馀层刀具进行了多次切削实验。
3.
TiAlN coatings were prepared on p-Si (111) subsurate by intermediate frequency sputtering technology using twinborn targets.
本文用中频孪生溅射技术在Si(111)基底上制备了富Al元素且Al/Ti原子比不同的TiAlN涂层,对其结构及表面形貌进行了研究,并在UMT-2MT摩擦试验机上进行摩擦试验,研究了不同原子比下的摩擦性能及摩擦系数,并对试验后的形貌进行了分析。
4) TiAlN/Ti coating
TiAlN/Ti涂层
1.
TiAlN/Ti coating was deposited by multiarc ion plating (MAIP) method with hotpresssintered TiAl alloy used as the target.
将Ti Al粉末冶金靶用多弧离子镀技术制备了TiAlN/Ti涂层。
5) TiN/TiAlN coating
TiN/TiAlN涂层
1.
The results show that the TiN/TiAlN coating is smooth and uniformity and the coating\'s adhesive strength to the matrix reaches 57.
结果表明,多弧离子镀TiN/TiAlN涂层均匀,TiN/TiAlN多层涂层与金属陶瓷之间的结合强度高达57。
6) TiAlN coated tool
TiAlN涂层刀具
1.
The high speed milling Cr12MoV quench steels of 50 HRC and 60 HRC hardness were tested with TiAlN coated tools.
针对硬度分别为50 HRC和60 HRC的Cr12MoV淬硬钢材料,采用TiAlN涂层刀具进行了高速铣削试验,重点研究了铣削方式、刀具螺旋角以及润滑方式等铣削条件对刀具磨损的影响。
补充资料：涂层技术
涂层技术
Coating Technology
藻套襄术Coating Teehnology见金属涂层;薄膜沉积技米。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条