1) desulfurization characteristics
固硫特性
1.
The desulfurization characteristics of shells and limestone have been studied by means of a LCT-2 thermobalance.
利用 L CT- 2型热天平实验研究了六种贝壳和四种石灰石的固硫特性 ,并利用电子显微镜与 XMA探测仪测定了其微观结构特性。
2.
This paper focuses on the results of an experimental study on the coal briquette desulfurization characteristics under the high temperatures specific to an industrial boiler as well as on the efforts aimed at improving the desulfurization efficiency.
主要介绍型煤在高温下的固硫特性和改善型煤固硫效率的试验研究结果。
2) sulfur retention characteristics
固硫特性
1.
On the basis of analyzing the sulfur retention mechanism of the biomass compound type of coal developed by the authors an experimental study was conducted of the sulfur retention characteristics of this type of coal.
对所研制的生物质复合型煤的固硫机理进行了分析 ,并对生物质复合型煤的固硫特性进行了试验研究 ,结果表明生物质复合型煤较一般型煤有更高的固硫率 ,当Ca/S=2 0、燃烧温度低于 90 0℃时 ,生物质复合型煤的固硫率可以达到 90 %以上 ;生物质复合型煤的固硫率受燃烧温度、生物质添加量、钙硫比等因素影响 ,加入铁系氧化物能增强生物质复合型煤的固硫性能。
2.
The sulfur retention mechanism and highly efficient sulfur retention characteristics of shell is analyzed when the latter serves as a sulfur retention sorbent during coal combustion.
对贝壳作为燃煤固硫剂的固硫机理和高效固硫特性进行了分析 ,并在模拟烟气条件下做了固硫特性试验 ,得出了固硫剂的粒度、升温速率、反应温度、反应时间、SO2 浓度等因素对固硫效果的影响 ,结果表明 ,贝壳作为高效燃煤固硫剂具有实用价
3) Temperature characteristics/Calcareous desulfurizer
温度特性/钙基固硫剂
5) curing characteristic
硫化特性
1.
The differences of thermooxiadative stability,curing characteristic and mechanical properties of hydrogenated nitrile rubber(HNBR) with different degree of hydrogenation were disscussed.
考察了丁腈橡胶(NBR)氢化过程中聚丁二烯的顺式-1,4-结构、反式-1,4-结构及乙烯基微观结构的变化,讨论了不同氢化度的氢化丁腈橡胶(HNBR)的热氧化稳定性、硫化特性和力学性能的差异。
2.
In this paper,the influence of the ratio of the CR/PUR blends on the curing characteristic,mechanical property,hot ageing resistance and thermo compression set of the blends were studied.
研究了共混比对氯丁橡胶/聚氨酯橡胶(CR/PUR)的硫化特性,硫化胶力学性能、耐热老化性能以及高温压缩永久变形的影响。
3.
The results showed that the two types of BR had similar thermostability and curing characteristics.
结果表明:两者的热稳定性相近,具有相似的硫化特性;BR9002L的耐机械降解性能稍好于BR9000;但BR9002L具有较小的相对分子质量、较窄的相对分子质量分布、较好的加工流动性、较严重的冷流性和较长的门尼焦烧时间。
6) curing behavior
硫化特性
1.
Effect of accelerator lanthanum O,O′-diisopropyldithiophosphate on the curing behavior of NR compound;
促进剂LaDiPDP对NR胶料硫化特性的影响
2.
The results showed that the molecule structure,curing behavior and physical properties of domestic products were identical to the imported counterparts,so the domestic products could replace the imports in tires and other rubber products;the molecule structure,curing behavior and physical properties of SSBR in different trademark were different,and t.
结果表明,同一牌号的国产SSBR分子结构与日本进口产品基本一致,胶料硫化特性以及硫化胶物理性能亦相当,可以相互替换用于轮胎及其它橡胶制品中;不同牌号的SSBR分子结构有所差别,胶料硫化特性不尽相同,硫化胶物理性能各有特点,可根据实际需要选用。
3.
The results showed that by using accelerator XT-580 instead of accelerator NOBS,the curing behavior and physical properties of compound changed slightly,and the tensile properties of sidewall compound and the abrasion resistance of tread compound were improved;comprehensive physical properties and the speed performance of 7.
结果表明,促进剂XT-580等量替代促进剂NOBS对胶料硫化特性和物理性能无不利影响,其中胎侧胶强伸性能和胎面胶耐磨性能稍有提高;试制的7。
补充资料：5-硫基-3-苯基-2-硫-1,3,4-硫代二唑,钾盐
CAS: 17654-88-5
分子式: C8H6N2S3
中文名称: 铋试剂II；3-苯基-1,3,4-噻二唑亚基-2,5-二硫酮；5-硫基-3-苯基-2-硫-1,3,4-硫代二唑,钾盐；铋试剂 II
英文名称: BismuthiolII；5-Mercapto-3-phenyl-2-thio-1,3,4-thiodiazole, potassium salt；4-thiadiazole-2-thione, 5-mercapto-3-phenyl-2h-3；4-thiadiazolidine-2,5-dithione, 3-phenyl-3；3-phenylbismuthol；5-mercapto-3-phenyl-2h-1,3,4-thiadiazole-2-thione；3,4-Thiadiazolidine-2,5-dithione, 3-phenyl-1
分子式: C8H6N2S3
中文名称: 铋试剂II；3-苯基-1,3,4-噻二唑亚基-2,5-二硫酮；5-硫基-3-苯基-2-硫-1,3,4-硫代二唑,钾盐；铋试剂 II
英文名称: BismuthiolII；5-Mercapto-3-phenyl-2-thio-1,3,4-thiodiazole, potassium salt；4-thiadiazole-2-thione, 5-mercapto-3-phenyl-2h-3；4-thiadiazolidine-2,5-dithione, 3-phenyl-3；3-phenylbismuthol；5-mercapto-3-phenyl-2h-1,3,4-thiadiazole-2-thione；3,4-Thiadiazolidine-2,5-dithione, 3-phenyl-1
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条