铸层,film,在线英语词典,英文翻译,专业英语

1) film

铸层

The experimental results show that film surface is flawless,but the thicknesses of different areas of base,wid.

工艺实验结果表明,整个变截面悬臂梁的铸层表面没有缺陷,但不同微电铸面积的基座、粗梁、细梁的铸层厚度不均匀,其中,铸层面积最大的基座铸层最厚,面积次之的粗梁的铸层厚度居中,面积最小的细梁的铸层最薄。

2) electroformed layer

电铸层

3) recast layer

再铸层

The harm of recast layer formed by laser drilling of Ni-based superalloys and the progress made on its control were introduced in this paper.

综述了镍基超合金激光打孔再铸层的危害 ,介绍了在控制再铸层方面的研究进

In order to solve the Achilles heel of recast layer and heat affected zone produced during laser machining,a new processing of neutral salt solution assisted laser machining(SALM) is put forward,which can remove recast layer and heat affected zone(HAZ) on-line by using the effect of salt solution on the thermal chemical reaction and continuing cooling effect of materials.

针对激光加工存在再铸层、热影响区(HAZ)的致命缺陷,提出了中性盐溶液辅助激光加工(SALM)方法,利用中性盐溶液对材料的热化学作用和持续冷却作用在线去除再铸层和热影响区。

Due to the rapid heating and cooling effects induced by the machining process, the recast layer will form on the surface of the part, which is very hard and contains many imperfections such as micro pits and micro cracks.

但是电火花加工后的孔内壁表面会形成再铸层。

4) coat-cast layer

涂铸层

5) re cast layer

重铸层

By means of high speed gas stream compound with coaxial cutting gas for pulsed Nd:YAG laser on cutting of ceramics,the technological parameters affected on the thickness of re cast layer and the exiting of crack in re cast layer were studied.

针对激光切割陶瓷产生的重铸层和裂纹，设计了超音速喷嘴，采用侧吹高速辅助气流与同轴切割气流复合技术，研究了激光加工工艺参数对重铸层及裂纹的影响规律，开发了获得最小重铸层厚度和裂纹长度的高效率激光切割方

6) uniformity

铸层均匀性

Study on uniformity of micro-electroformed device;

微电铸器件铸层均匀性的研究

参考词条

MD振动赛若金

补充资料：衡阳钢管厂水平连铸机生产连铸圆管坯

衡阳钢管厂水平连铸机生产连铸圆管坯

　　衡阳钢管厂水平连铸机生产连铸圆管坯
　　

说明：补充资料仅用于学习参考，请勿用于其它任何用途。

首页 \| 翻译 \| 影视 \| 论坛 \| 索引复合电铸层激光熔铸层纳米复合电铸层纳米复合铸层

1) film 铸层 1. The experimental results show that film surface is flawless,but the thicknesses of different areas of base,wid. 工艺实验结果表明,整个变截面悬臂梁的铸层表面没有缺陷,但不同微电铸面积的基座、粗梁、细梁的铸层厚度不均匀,其中,铸层面积最大的基座铸层最厚,面积次之的粗梁的铸层厚度居中,面积最小的细梁的铸层最薄。 2) electroformed layer 电铸层 3) recast layer 再铸层 1. The harm of recast layer formed by laser drilling of Ni-based superalloys and the progress made on its control were introduced in this paper. 综述了镍基超合金激光打孔再铸层的危害 ,介绍了在控制再铸层方面的研究进 2. In order to solve the Achilles heel of recast layer and heat affected zone produced during laser machining,a new processing of neutral salt solution assisted laser machining(SALM) is put forward,which can remove recast layer and heat affected zone(HAZ) on-line by using the effect of salt solution on the thermal chemical reaction and continuing cooling effect of materials. 针对激光加工存在再铸层、热影响区(HAZ)的致命缺陷,提出了中性盐溶液辅助激光加工(SALM)方法,利用中性盐溶液对材料的热化学作用和持续冷却作用在线去除再铸层和热影响区。 3. Due to the rapid heating and cooling effects induced by the machining process, the recast layer will form on the surface of the part, which is very hard and contains many imperfections such as micro pits and micro cracks. 但是电火花加工后的孔内壁表面会形成再铸层。 4) coat-cast layer 涂铸层 5) re cast layer 重铸层 1. By means of high speed gas stream compound with coaxial cutting gas for pulsed Nd:YAG laser on cutting of ceramics,the technological parameters affected on the thickness of re cast layer and the exiting of crack in re cast layer were studied. 针对激光切割陶瓷产生的重铸层和裂纹，设计了超音速喷嘴，采用侧吹高速辅助气流与同轴切割气流复合技术，研究了激光加工工艺参数对重铸层及裂纹的影响规律，开发了获得最小重铸层厚度和裂纹长度的高效率激光切割方 6) uniformity 铸层均匀性 1. Study on uniformity of micro-electroformed device; 微电铸器件铸层均匀性的研究参考词条 MD振动赛若金补充资料：衡阳钢管厂水平连铸机生产连铸圆管坯衡阳钢管厂水平连铸机生产连铸圆管坯　　衡阳钢管厂水平连铸机生产连铸圆管坯　　说明：补充资料仅用于学习参考，请勿用于其它任何用途。
©2008 dictall.com