1) wet picking speed
湿拉毛速度
1.
GS-235 water-resistance agent, which has no potential of polymerization, can only react with -OH and -COOH, thus the traditional glyoxal resin’s defects of curing tardiness and brightness reversion were overcome, the dosage was lowered and printability and wet picking speed were improved.
GS-235抗水剂因自身不会发生聚合反应,仅与-OH及-COOH反应,因而克服了传统乙二醛树脂熟化慢及返黄的缺点,降低了用量,提高了纸张适印性及湿拉毛速度。
2) galling speed
拉毛速度
1.
The galling speeds of C 14 ?K 80 and non-ionic starch increase by 44%,20%,46%respectively;The effect o f LS -2is better than that of CCS -3,an d their mixture can get higher strength.
其中使用C14型、K80型及非离子淀粉抄纸的拉毛速度分别比工厂所用淀粉的手抄片提高44%、20%、46%;工厂所用LS-2型比CCS-3型的增强效果好,当LS-2型与CCS-3型按3∶2比例抄纸时,拉毛速度提高近32%。
3) picking velocity
IGT拉毛速度
4) wet picking
湿拉毛
1.
The performances of wet picking and wet resistance on surface of three art paper samples were studied using IGT printability tester by changing printing speed and the amount of fountain solutions.
利用IGT印刷适性仪模拟实际印刷,以铜版纸为纸样,通过改变印刷速度和润版液供给量等印刷条件,考察了3种纸样所产生的湿拉毛和湿排斥效果。
2.
The impact of wet picking and wet resistance of offset paper were studied using IGT printability tester to simulate the real printing process.
在实验室中利用IGT印刷适性仪模拟实际印刷,以胶版纸为纸样,通过改变印刷速度和润版液的供给量等印刷条件,考察了3种胶版纸所产生的湿拉毛和湿排斥效果。
3.
The wet picking and wet resistance of offset papers and art papers were studied by using IGT-gst2 printability tester according to change printing conditions as printing speed and the amount of fountain solutions.
利用IGT-gst2印刷适性仪模拟实际印刷,以胶版纸和铜版纸为纸样,通过改变印刷速度和润版液供给量等印刷条件,考察了它们的湿拉毛和湿排斥性能。
5) capillary humidity
毛管湿度
6) surface intensity
拉毛强度
1.
The result shows that the stability and viscidity of the coating is improved and the surface intensity of coated paper is increased.
试验结果表明,羧甲基纤维素钠不仅能改善涂料的稳定性,提高涂层的表面拉毛强度,还能起到辅助胶粘剂的作用。
补充资料：湿基湿含量
分子式：
CAS号：
性质：为了表示湿物料的含湿（水）量，常以单位质量湿物料为基准表示所含湿分（水分）的质量，称为湿基湿含量。参见湿含量条目。
CAS号：
性质：为了表示湿物料的含湿（水）量，常以单位质量湿物料为基准表示所含湿分（水分）的质量，称为湿基湿含量。参见湿含量条目。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条