1) Gear ratio error
传动比误差
2) transmission error
传动误差
1.
Design of Transmission Error Sampling Module Based on CPLD;
基于CPLD设计的高速机械传动误差采集模块
2.
A Phase-comparing Method Based on 8254 for Measuring Transmission Error;
基于可编程定时计数器8254的传动误差比相测量方法
3.
Research on the Key Technique of the Front CPU in Distributed Transmission Error Testing System;
分位式传动误差测试系统下位机关键技术研究
3) transmission errors
传动误差
1.
Design of geometry transmission errors of helical face-gear drive;
斜齿面齿轮几何传动误差的设计
2.
Three meshing points on the tooth surface were designed according to the contact pattern and transmission errors.
根据齿面印痕的位置、方向及传动误差幅值的要求,在齿面上设计三个啮合点,通过对这三个啮合点的控制,达到对齿面啮合质量的全程控制。
3.
The transmission errors and the distribution of contact path were simulated with computer in the misaligned gear drive.
通过计算机仿真了在装配误差存在条件下传动误差和啮合印痕在齿面的分布状况。
4) Errors in Driving Chain
传动链误差
1.
Measuring and Analysis on Errors in Driving Chain of Thread Grinder;
螺纹磨床传动链误差的测量与分析
5) transfer ratio error
传送比率误差
6) differential driven ratio
差动传动比
1.
In this paper, the relation between differential driven ratio accuracy and the common normal length error of cylindrical bevel wheel has been found by experimental method, which provides a efficient way for cylindrical bevel wheel manufacturer to control the common normal length error of the wheel.
通过实验研究,寻找出差动传动比的精度与斜齿圆柱齿轮的公法线长度误差的关系,从而为斜齿圆柱齿轮的加工提供一个可以控制斜齿圆柱齿轮公发线长度误差的有效方法。
补充资料：传动：摆线针轮传动
由外齿轮齿廓为变态摆线﹑内齿轮轮齿为圆销的一对内嚙合齿轮和输出机构所组成的行星齿轮传动。除齿轮的齿廓外﹐其他结构与少齿差行星齿轮传动相同。摆线针轮行星减速器的传动比约为6～87﹐效率一般为0.9～0.94。图 轮齿曲线的形成 为轮齿曲线的形成原理。发生圆在基圆上滚动﹐若
大於r1﹐M'点画出的是长幅外摆线﹔若
小於r1﹐M''点画出的是短幅外摆线﹔用这些摆线中一根曲线上的任意点作为圆心﹐以针齿半径rz为半径画一系列圆﹐而后作一根与这一系列圆相切的曲线﹐得到的就是相应的长幅外摆线齿廓或短幅外摆线齿廓﹐其中短幅外摆线齿廓应用最广。用整条短幅外摆线作齿廓时﹐针轮和摆线轮的齿数差仅为1﹐而且理论上针轮有一半的齿数都与摆线轮齿同时嚙合传动。但如果用部分曲线为齿廓就可得到两齿差和三齿差的摆线针轮传动。用长幅外摆线的一部分作轮齿曲线时﹐其齿廓与圆近似﹐并与针齿半径相差不大﹐因此可用它的密切圆弧代替。摆线针轮传动的优点是传动比大﹑结构紧凑﹑效率高﹑运转平稳和寿命长。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条