2) non-distortion welding
动态控制焊接变形
3) monitor welding deformation
监控焊接变形
1.
It also explained the technique to monitor welding deformation under free status, with the shims to realize the four studs spiral progression rim plate piling, to adopt different size of tight bolts and heaters to heat up the rim plates to reach the expected expanding capacity, to put s.
采用了自由状态下监控焊接变形;加填隙片,旨在呈4头螺旋线型堆叠磁轭冲片;采用了不同规格的压紧螺杆;又采用管状电阻加热棒加热磁轭,致使达到应有的膨胀量,加装垫片为预紧量,使磁轭热套于圆盘式结构支架上;并采用了多种组合键调整控制联结等新结构、新工艺、新技术和新标准。
4) welding distortion
焊接变形
1.
Using thermal tensioning and trailing intense cooling simultaneously to reduce welding distortion;
温差拉伸和随焊激冷配合使用控制焊接变形
2.
Review on prediction of welding distortion;
焊接变形预测技术研究进展
3.
Study on the instantaneous welding distortion of diaphragm in steam turbine;
蒸汽轮机自带冠静叶隔板瞬时焊接变形研究
5) welding deformation
焊接变形
1.
Numerical simulation on welding deformation of spherical cap structure based on ABAQUS;
基于ABAQUS平台对球冠结构焊接变形的数值试验
2.
Prediction of Welding Deformation on the Beam of Thin Wall Box;
薄壁箱形梁的焊接变形预测
3.
Prediction of welding deformation in mild steel pipe using thermal elastic plastic finite element method;
采用热弹塑性有限元方法预测低碳钢钢管焊接变形
6) welding deformations
焊接变形
1.
The paper emphatically analyzes the influence on the truss frame welding quality of the welding groove form and the welding deformations and the welding technology,the testing and research of the technology for the type of the welding and the factor of infecting welding deformations ect.
着重分析了焊接坡口形式、焊接变形和焊接工艺等对箱形井架制造焊接质量的影响,并对焊接坡口形式、影响焊接变形的因素等进行了工艺试验研究,制定出合理的制造工艺和完善的工艺规程。
2.
This paper introduces the structural features of tube air-preheater, analyzes on the reasons of the welding deformations in the manufacturing process, and describes in detail the method of controlling the welding deformations.
文章介绍了管式空气预热器的结构特点 ,对制做中焊接变形产生的原因进行了分析 ,并对控制焊接变形的措施作了详尽的叙
3.
A nondestrucive testing prcedure is proposed in the paper to determine the welding residual stresses with the aid of boundany element method, in which the welding deformations of the welded structures are taken as the known boundary conditions, through the boundary integral equation and its discrete form BDM, the problem of welding residual stresses is resolved.
提出了边界元辅助焊接残余应力的无损测试方法,该方法将焊接变形作为已知边界条件,通过边界积分方程及其离散形式──边界元法来求解焊接残余应力,推导出了计算公式,构造了算法和步骤,编制了相应的计算机程序,通过用应力释放法对几块典型焊接试板中的二维焊接残余应力进行实测,验证了该方法的合理性与可行性。
补充资料：焊接变形
焊接变形
distortion in weldments
hanjle blanxing 焊接变形(distortion in weldments)全属 焊接时或焊接后，由于不均匀加热和不均匀冷却引起 的金属焊接结构的变形。焊接变形大致可分为8类: (l)纵向收缩变形。构件焊后在焊缝方向发生收缩，如 图1中的△乙。(2)横向收缩变形。构件焊后在垂直焊缝 方向发生收缩，如图1中的△召。(3)弯曲变形(图2)。 构件焊后发生弯曲。弯曲可由焊缝的纵向收缩引起，也 可由焊缝横向收缩引起。(4)角变形(图3)。焊后构件堰票到{副}渠囊到+目{ 图1纵向和横向收缩变形的平面围绕焊缝产生的角位移。(5)波浪变形(图4)。焊后构件呈波浪形，在薄板焊接时最容易发生。(6)错边变形(图5)。在焊接过程中，两焊接件的热膨胀不一致，可能引起长度方向上的错边和厚度方向上的错边。(7)扭转变形(图6)。焊后在结构上出现的扭曲。(8)张开变形(图7)。平板对接时，焊炬前方出现张开现象。一窿白一‘ 之立童鱼宝 b 图2弯曲变形 a一焊缝纵向收缩引起;b一焊缝横向收缩引起 一甲 图3角变形处遥乡、气蛋建乡 图4波浪变形业久二多酬 ab 图5错边变形 a一无点固泌一有点固 霆葬冀霎 图6扭转变形巨弓 图7张开变形
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条