1) congregator-filled with F-AC gradular material
F-AC粒料型聚结器
2) parison accumulator
型坯聚料器
3) junction particle detector
结型粒子探测器
4) AC/AC converter
AC/AC变换器
1.
Novel AC/AC converters with high frequency ac link are composed of two kinds of AC/AC converters,which are voltage mode based on Forward converter and current mode based on Flyback converter.
新颖的高频交流环节AC/AC变换器,包括基于Forward变换器的电压源型和基于Flyback变换器的电流源型两种。
2.
Based on Flyback converter, a novel circuit structure and topologic family of current-mode AC/AC converters with high frequency ac link are proposed.
提出了基于反激Flyback变换器的电流源高频交流环节AC/AC变换器电路结构与拓扑族。
3.
The novel full-bridge mode AC/AC converters with high frequency link are constituted of input cycloconverter, high frequency transformer, output cycloconverter, input and output filters.
新颖的全桥式高频环节AC/AC变换器,由输入周波变换器、高频变压器、输出周波变换器以及输入、输出滤波器构成,包括全桥全波式和全桥桥式拓扑。
5) AC/AC variable frequency converter
AC/AC变频器
1.
Introducing fuzzy-PI control method to the AC/AC variable frequency converter speed-regulated system of synchronous motor and replacing speed-regulator controlled by PI by fuzzy controller,the simulation experiment result expresses that all indexes of fuzzy control method are basically better than those of traditional PI control.
将模糊控制方法引入到AC/AC变频器同步电机调速矢量控制系统中,以模糊PI控制器代替传统的PI控制器。
6) AC-AC converter
AC-AC变换器
1.
A circuit configuration and circuit topological family of the current(Boost) mode AC-AC converter with high frequency link are proposed.
提出电流(Boost)型高频链AC-AC变换器电路结构与拓扑族,它是由输入滤波器、储能电感、输入周波变换器、高频变压器、输出周波变换器和输出滤波器依序级联构成。
2.
And the basic multi-level AC-AC converters are obtained by applying the AC multi-level switch unit in the basic converters.
将直流开关单元进行组合,得到交流多电平开关单元,并将这种多电平交流开关单元运用到基本变换器中,得到基本多电平AC-AC变换器,然后将基本多电平AC-AC变换器进行组合,提出了一族组合式多电平AC-AC变换器,(包括Buck TL(三电平three level的缩写)-Boost组合式三电平AC-AC变换器;Buck-Boost TL组合式三电平AC-AC变换器;Buck TL-Boost TL组合式三电平AC-AC变换器),研究了Buck TL-Boost组合式三电平AC-AC变换器的工作原理和控制方案,实现了分压电容的均压策略,并通过PSPICE软件仿真,验证了组合式多电平AC-AC变换器拓扑方法的可行性和工作原理的正确性。
补充资料：粒料
分子式：
分子量：
CAS号：
性质：颗粒状物质。常指热塑性塑料成型加工用的原料。由粉状树脂经熔融、挤出和切粒后得到。在塑料成型加工中使用粒料可保证树脂熔体的均匀有效供给，利于充满模腔，制得密实制品。
分子量：
CAS号：
性质：颗粒状物质。常指热塑性塑料成型加工用的原料。由粉状树脂经熔融、挤出和切粒后得到。在塑料成型加工中使用粒料可保证树脂熔体的均匀有效供给，利于充满模腔，制得密实制品。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条