1)  heat-resistance rubber
耐热橡胶
2)  heat resistant rubber
耐热橡胶
1.
Introduced the grade classification of heat resistant rubber, the using temperature andproperty of formulas for heat resistant samples, and described each formula in detail.
介绍了耐热橡胶的等级划分,各种橡胶的使用温度和性能特点,及13种橡胶(天然橡胶、聚氨酯橡胶、丁苯橡胶、顺丁橡胶、氯丁橡胶、丁腈橡胶、氯磺化聚乙烯橡胶、氯醚橡胶、丁基橡胶、乙丙橡胶、丙烯酸酯橡胶、氟橡胶、硅橡胶)的78个耐热配方实例,并对配方做了简要说明。
3)  heat resistant
耐热
1.
Synthesis of novel high heat resistant epoxy resin containing naphthyl structure;
一种新型含萘环结构高耐热型环氧树脂的合成
2.
Study on heat resistant epoxy resin adhesive with high peel strength cured at room temperature;
室温固化高剥离耐热环氧树脂胶粘剂
3.
Development of Casting Dual-Phase Heat Resistant Alloy Fe-Cr-Ni-Al;
铸造Fe-Cr-Ni-Al双相耐热合金的研制
4)  heat-resistance
耐热
1.
The tray is a typical frame-shaped casting,it should have the abilities of heat-resistance,heat impact-resistance and crack-resistance through using different technologies and improving the technologies,make a simulated analyze on pouring system through CAST soft,investment casting CAE software.
薄壁耐热钢托盘属于典型的筐架结构型铸件,要求其有较高的耐热性、耐热冲击及抗裂能力。
2.
The mechanism of wear-resistance,heat-resistance and corrosionresistance of high chloride cast iron are analyzed respectively.
分析了高铬铸铁具有的抗磨、耐热、耐蚀性机理。
3.
A new duple-phase heat-resistance steel used at above 1 000 ℃ was obtained by adding some Ni to an original ferrite heat-resistance steel.
在高铬铁素体单相耐热钢的基础上,加入一定量的镍,得到一种新的奥氏体-铁素体双相耐热钢,并对该铬镍双相耐热钢的组织特征及常温和高温性能进行了测定。
5)  heat-resistant
耐热
1.
Study on preparation and properties of heat-resistant epoxy adhesive cured at room temperature;
室温固化耐热环氧胶粘剂的制备与性能研究
2.
Fire test on a non-heat-resistant fireproof glass with down-flowing water film;
带雨淋水膜的非耐热防火玻璃的火灾试验(英文)
3.
Research present state and development of heat-resistant epoxy adhesive cured at room temperature;
室温固化耐热环氧胶粘剂的研究现状及进展
6)  heat resistance
耐热
1.
Influence of three kinds of surface dispersants on the activity and heat resistance of Ru/AC catalyst for ammonia synthesis;
3种表面分散剂对Ru/AC氨合成催化剂的活性和耐热性的影响
2.
Effect of several kinds of antioxidant on heat resistance properties of chlorinated polyethylene;
防老剂对氯化聚乙烯耐热性能的影响
3.
Casting Magnesium Alloy of Mg-Nd-Zn-Zr Series with Heat Resistance and High Strength;
Mg-Nd-Zn-Zr耐热高强铸造镁合金
参考词条
补充资料：耐热橡胶
分子式：
CAS号：

性质：一般指长时间使用在100℃以上至200℃左右的橡胶。硫化橡胶在高温或热氧长时间作用下，分子链被破坏或进一步交联，则发生橡胶软化或脆化。提高橡胶的耐热性能有以下三个方面。（1）选择耐热性的生胶。橡胶的耐热稳定性决定于分子结构及键合强度。常用耐热橡胶的耐用温度可归纳为：氯丁、丁腈及氯醇橡胶为100～130℃；丁基、三元乙丙橡胶及氯磺化聚乙烯橡胶为130～150℃；丙烯酸酯橡胶、氢化丁腈橡胶为150～180℃；硅橡胶、氟橡胶为180～200℃；硼硅橡胶、全氟醚为>250℃。（2）橡胶的硫化体系。具有最佳耐热交联结构的硫化体系如下：天然橡胶丁腈橡胶用镉镁硫化体系或过氧化物硫化体系；三元乙丙橡胶用过氧化物（过氧化二异丙苯）硫化体系；丁基橡胶用树脂化体系。（3）采用高效耐热型防老剂。常用对苯二胺类的4010NA及酮胺缩合物类的RD，BLE等。其次填充剂中，宜用白炭黑、氧化锌、氧化镁。必须用炭黑补强时，宜用槽法炭黑。

说明：补充资料仅用于学习参考，请勿用于其它任何用途。