1) Gear Steel 20CrMoH
20CrMoH齿轮钢
1.
Practice on Production of Gear Steel 20CrMoH by Converter-Bloom Concasting Process at Panzhihua Iron and Steel;
攀钢采用120t顶底复吹转炉→LF+RH精炼→大方坯连铸(280mm×380mm)→热轧工艺生产规格为Φ25～60mm的20CrMoH齿轮钢,检验结果表明,成品检验结果为成分(%):C0。
2) Steel 20CrMoH
20CrMoH钢
1.
Control of TiN Inclusion in Ultra-low Oxygen Steel 20CrMoH and 60Si2MnA;
20CrMoH钢中TiN夹杂较少,60Si2MnA钢中TiN占夹杂总量的50%～60%。
3) 20CrMnTiH gear steel
20CrMnTiH齿轮钢
1.
Present situation and quality control of 20CrMnTiH gear steel in Laiwu Steel;
莱钢20CrMnTiH齿轮钢的质量现状与质量控制
2.
Practice of Process for Increasing Ratio of Qualified 20CrMnTiH Gear Steel Products with Non-metallic Inclusion Examination
提高20CrMnTiH齿轮钢夹杂物合格率的工艺实践
3.
Starting with the requirements in serviceability and malleability which must be met during the machining of gears,based on the present situation of 20CrMnTiH gear steel in the Special Steel Plant,this paper presents the main points in quality control of the steel during its production and puts forth some improvement suggestions.
主要从齿轮加工时必须满足的使用性要求和加工性要求两个方面着手,结合特钢厂20CrMnTiH齿轮钢的质量现状,介绍了该钢种生产时的质量控制要点,并提出改进建议。
4) Gear Steel
齿轮钢
1.
Multi-Field Coupled Analysis on Quenching Process of Gear Steel;
齿轮钢淬火过程多场耦合分析
2.
Effect of deformation of austenite on continuous cooling transformation for 22CrSH gear steel;
奥氏体变形对22CrSH齿轮钢连续冷却相变的影响
3.
The Development of the High Grade Gear Steel SCM420H;
高等级齿轮钢SCM420H的开发研制
5) Gear Steel 28MnCr5
28MnCr5齿轮钢
1.
Effect of LF(VD) Refining Process on Control of Sulphur and Sulphide in Gear Steel 28MnCr5;
LF(VD)精炼工艺对控制28MnCr5齿轮钢中硫和硫化物的影响
6) Gear Steel 20CrMnTiH
20CrMnTiH齿轮钢
1.
Process Practice of Gear Steel 20CrMnTiH Production by 150 mm×150 mm Concasting Billet at Laiwu Steel;
莱钢150mm×150mm连铸坯生产20CrMnTiH齿轮钢的工艺实践
2.
Process Practice of Gear Steel 20CrMnTiH Production with 70 t LD-LF-CC Flow Sheet at Chengde Jianlong Steel
承德建龙70tLD-LF-CC流程生产20CrMnTiH齿轮钢的工艺实践
3.
Pilot Production of Narrow Hardenability Band Gear Steel 20CrMnTiH by 120 t Converter-LF+RH Process at Panzhihua Steel;
攀钢采用120 t转炉-130 t LF+RH-280 mm×380 mm方坯连铸-热轧工艺生产Φ25～160 mm 20CrMnTiH齿轮钢(%:0。
补充资料：A3钢试片在济南埋20年后的腐蚀情况
A3钢试片在济南埋20年后的腐蚀情况
A3钢试片在济南埋20年(1 964～1 983芷)后的黯蚀情况\;/俘{“少_，喃IJ扮川竺广{「从、抽人’、1一、洲一比、一了J」一.; 川「乙勺{一尸一L一」.{’l卜朽「列
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条