说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 跑偏开关
1)  Running-away preventing switch
跑偏开关
2)  polarization switching
偏振开关
1.
In this paper,polarization switching performances and polarization bistability performances in VCSEL subjected to optical feedback had been investigated.
本文主要研究了外光反馈对VCSEL偏振开关特性和偏振双稳特性的影响。
2.
Based on the rate equations describing the dynamic characteristics of the master and slave vertical cavity surface emitting laser (M-VCSEL,S-VCSEL),under the modulation of pulsed bias current,the polarization characteristics of M-VCSEL output and the polarization switching performance of S-VCSEL subjected to optical pulse output from the M-VCSEL have been investigated.
基于描述主、副垂直腔表面发射激光器(M-VCSEL,S-VCSEL)动态特性的速率方程,研究了M-VCSEL在脉冲电流调制下,输出光脉冲的偏振特性,以及S-VCSEL在M-VCSEL输出光脉冲的注入下,其偏振开关特性。
3)  offset switch
偏移开关
4)  running deviation
跑偏
1.
This paper analyzes the running deviation of conveyor belt,puts forward precautionary measures of running deviation under different situation,studies on corrective measures,self-corrective measures and its principle in de.
输送带跑偏是带式输送机运行中最常见的故障,严重影响设备的寿命及生产。
2.
In aluminium strip hot rolling process,because the landscape orientation parameters of the workpiece and the rolling mill are not even,there is always departure between the center line of the workpiece and the assumed center line,which is called running deviation.
铝带热连轧过程中,铝带和轧机横向特性参数不均易引起铝带中心线偏离轧制系统设定中心线,产生跑偏现象。
3.
This paper introduces the reasons of belt coveryor's belt running deviation,and some methods to adjust deviation.
介绍带式输送机输送带跑偏的原因 ,以及调偏的一些方法。
5)  deviation [英][,di:vi'eɪʃn]  [美]['divɪ'eʃən]
跑偏
1.
Intelligent control system for edge position deviation of narrow fabrics;
矫正织物蛇行跑偏运动的智能纠偏系统
2.
The automatic system of conveyer belt deviation;
带式输送机跑偏自动校正系统
3.
The measures analysis of occurring deviation while installing prevention embryonic plate of heating-furnace;
加热炉炉底机械安装预防板坯跑偏措施分析
6)  rolling deviation
跑偏
1.
Rearch for rolling deviation value in unsymmetrical plate/strip rolling;
非对称情况下板带轧制跑偏的研究
2.
At the same time,rolling deviation is used.
板形理论中条元法的计算精度在很大程度上依赖于金属出口横向位移函数的初值,在非对称情况下采用以往研究中使用对称情况下的初值会有一定误差,为此以非对称函数拟合带材入、出口处横向厚度分布,同时引入跑偏概念,利用最小能量原理,由欧拉微分方程求得非对称情况下出口处金属横向位移函数,并计算了前张应力的横向分布,计算结果符合试验规律。
补充资料:跑了和尚跑不了寺
1.见"跑了和尚跑不了庙"。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条