1) bubble growth
气泡成长
1.
This paper studied and established the mathem atical model for bubble growth in polymer during microcellular foaming, for controlling the cells size and their distribution.
研究、建立了聚合物微孔发泡过程中的气泡成长数学模型,以控制发泡过程中的泡孔尺寸大小和尺寸分布。
2) air bubble
气泡
1.
Measurement of effective permittivity for solution chemical reaction and analysis of air bubble effect;
液相化学反应介电常数的测量与气泡影响分析
2.
Formation for air bubble in cement paste and its influence on the strength;
水泥石气泡的形成及其对强度的影响
3.
On the prevention of air bubbles and sand grains in the surface of tunnel secondary lining;
浅谈隧道二衬表面气泡和泛砂质量通病的防治
3) gas bubble
气泡
1.
Modeling and analyzing of low pressure pipeline transients accompanying gas bubbles and cavitation;
伴随气泡和气穴低压管路瞬态的建模与分析
2.
Parameter identification of gas bubble model in pressure pulsations using genetic algorithms;
采用遗传算法对压力脉动过程中气泡模型参数的辨识
3.
The influence of casting speed,argon blowing flow and in- sertion depth of submerged nozzle on the distribution of gas bubble in mould is investigated by water modelling.
对热轧板孔洞缺陷形成的原因进行了分析,指出连铸过程操作参数控制不合理是产生该种缺陷的主要因素;利用水模试验研究了水口插入深度、拉速、吹氩量等因素对结晶器内气泡分布的影响,在此基础上提出了治理热轧板孔洞缺陷的措施,取得了较好的效果。
4) bubbles
气泡
1.
Modeling of Energy Distribution of Bubbles of Burning Fluidized Bed;
燃烧流化床气泡能量分布模型
2.
Thermodynamics Analysis of the Relationship Between Pressure and Fugacity of Methane in Hydrogen Attacked Bubbles;
氢蚀气泡内甲烷压力与逸度关系的热力学分析
3.
Study on back light-scattering property of bubbles in ship wake;
舰船尾流气泡后向光散射特性研究
5) void
气泡
1.
Study Development of Mechanism for Void Formation and Elimination During RTM Processing;
RTM工艺过程中气泡形成机理及排除方法研究进展
2.
The Application of Resin s Temperature Deference to the Void Problem;
树脂温差在解决气泡问题上的运用
3.
The literatures concerning void formation during resin transfer molding process were collected and reviewed.
总结了关于RTM(树脂压铸)工艺中气泡缺陷的文献报道,对RTM中气泡缺陷的形成机理、影响因素及各研究者提出的消泡方法、理论和模型进行了概述,同时对RTM工艺中气泡缺陷的研究现状给予充分关注,并对RTM缺陷研究的未来方向进行了展望。
6) bubble
气泡
1.
River system repair technology of super-micro bubble;
超微细气泡水体修复技术
2.
Coalescence time measurement of two bubbles and its influence factors;
双气泡间的聚并时间测量及其影响因素
3.
Simulation of bubble hydrodynamics in viscors liquid;
粘性液体中气泡流体力学特性的模拟研究
参考词条
补充资料：表面气泡
表面气泡
skin hole
b iaomian qiPao表面气泡(skin hole)钢锭表面上一些开口的孔眼。是钢中气体析出于钢锭表皮而形成的;钢锭模壁潮湿，或使用的保护渣潮湿，在浇注时蒸发出气体，也会使钢锭形成表面气泡。它会使轧材出现深口、裂痕、甚至海绵面等缺陷。其防止措施主要是降低钢液气体含量，保持锭模和保护渣干操。 (汪建农)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。