1) high plasticity
高塑性
1.
In this paper, the chemical composition, melting and rolling technology, microstructure and properties of steels with high plasticity, low yield point applied to earthquake damping device were studied.
研究了具有高塑性低屈服点的减震器用钢化学成分、冶炼、轧制、组织和性能。
2.
Based on the model tests of seepage\|induced consol idation, the consolidation characteristics of soft clay with high plasticity und er seepage pressure is studied under the condition of 1\|D non\|linear consolida tion.
本文通过渗透固结模型实验 ,对渗透压力下高塑性粘土一维非线性固结特性进行研究 ,确定了固结过程中压缩性关系 (e-σ′)、渗透性关系 (e-k)表达式 ,从而为该渗透固结机理应用到土坝水平防渗措施中粘土铺盖裂缝的淤填、淤积铺盖防渗性能的提高等方面提供理论依
2) Hot Ductility
高温塑性
1.
A Study on Hot Ductility of Q235B Steel Thin Slab;
Q235B薄板坯高温塑性的研究
2.
Gleeble-1500 was used to test the hot ductility of rolled medium-carbon 45 steel bars from continuously cast billets with sulphur contents of 0.
06%)轧材及连铸坯的高温塑性。
3.
This paper describes comprehensively the hot ductility of Nb-bearing microalloyed steel in different temperature range.
综述了不同温度区间含铌微合金钢的高温塑性。
3) high temperature plasticity
高温塑性
1.
A kind of technology which can improve the mechanical properties and high temperature plasticity of MoSi 2 heating element was introduced by means of synthesis of MoSi 2,size of powder, additive and sintering.
从二硅化钼合成、粉料粒度、添加剂选择、烧结工艺等方面研究提高二硅化钼发热体的力学性能和高温塑性。
2.
The slabs with these cracks were analyzed by means of high temperature plasticity,macrostructure,microstructure and inclusion test.
对有裂纹的连铸板坯进行了高温塑性试验、低倍、金相组织和夹杂物分析。
4) high temperature ductility
高温塑性
1.
365, the high temperature ductility and stress rupture life were reduced because large MC films, dendritic flake M6C and fine M23C6 films precipitated at grain boundaries.
008%时,因固溶B/C(原子比)很低,晶界析出大尺寸MC薄膜和M6C枝晶片以及薄膜状M23C6,不利于高温塑性和持久寿命。
2.
Contrary to be crack sources and make mechanical properties of alloys deteriorate as it has been always considered, η phase was found to have little effect on room temperature properties and furthermore, it improved the high temperature ductility of the alloy via blocking the grain boundary slip due to it.
通过对一种Fe-Ni-Cr合金进行过时效后晶界上析出η相的研究发现,由于晶界η相与合金基体保持共格关系,η相对合金的室温性能影响不大;并且在高温变形条件下η相形成凸起,阻碍晶界滑动,减小在晶角处的应力集中,从而提高合金的高温塑性。
5) high-temperature plasticity
高温塑性
1.
The results show that the intracrystalline absorption of oxygen and phosphorus dueto the segregation of element B on the grain boundary is restrained and the properties on thegrain boundary as well as the high-temperature plasticity of the steel are imp.
用俄歇能谱仪、电子显微镜和ＷＪ－１０型机械式万能材料试验机，分析了奥氏体热作模具钢的晶界成分，观察了晶界组织，测试了钢的力学性能，结果表明：微量元素硼偏聚于晶界，抑制了氧和磷的晶界内吸附，改善了晶界性能，提高了钢的高温塑性。
2.
The results show that the high-temperature plasticity of low-carbon steel with γ→γ+α→γ thermal history is the worst of all.
利用热模拟方法研究了不同热经历对电炉低碳钢高温力学性能的影响,结果表明,具有γ→(冷却)γ+α→(加热)γ热经历的低碳钢高温塑性最差,根据这一结果制定了传搁温度低于 A_(rl)的钢锭红送工艺。
6) high-plastic soil
高塑性土
1.
Conbined with a case study,the strength characteristics of high-plastic soil in saturating of capillary is studied through soaking CBR test.
结合一工程实例,通过浸水CBR试验,分析高塑性土在毛细饱水情况下的强度特征,揭示高塑性土的路用特性,并将室内研究成果结合现场工艺试验,研究在不添加外掺剂的前提下,直接利用高塑性土填筑路基的途径和方法。
2.
The application of TDR technology to moisture monitoring of high-plastic soil subgrade overcomes the shortcoming of unable to carry out deep,continuous,positioning testing of the traditional moisture test.
将TDR技术应用于高塑性土路基的含水率监测,克服了传统含水率测试无法进行路基深层、连续、定位观测的缺点。
补充资料：高温塑性
分子式：
CAS号：
性质：在高温下材料所具有的塑性。主要取决于组成中的杂质所形成的低共熔物的性质、数量、分布及晶粒间的结合状态等。耐火材料的高温塑性有利于缓冲热应力，但对高温体积稳定性和高温强度不利。
CAS号：
性质：在高温下材料所具有的塑性。主要取决于组成中的杂质所形成的低共熔物的性质、数量、分布及晶粒间的结合状态等。耐火材料的高温塑性有利于缓冲热应力，但对高温体积稳定性和高温强度不利。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条