1) re-solution
重固溶
1.
The effects of re-solution and re-ageing on mechanical properties and microstructural characteristics of 7175 aluminum alloy were evaluated by means of scanning electron microscopy(SEM),transmission electron microscopy (TEM),mechanical properties and conductivity tests.
采用拉伸试验、电导率测试及电镜观察等方法,研究了重固溶后低温-中温-高温(LMH)再多级时效制度对7175铝合金组织与性能的影响。
2.
The effect of low temperature-high temperature-low temperature multistage re-aging system on the structure and the property of 7175 aluminum alloy after re-solution was studied by means of stretching test,electrical conductivity test and electroscope observation.
采用拉伸试验、电导率测试及电镜观察等方法,研究了重固溶后再经低温-高温-低温(LHL)多级时效处理对7175铝合金组织与性能的影响。
3.
The effect of re-solution and re-ageing on microstructural and mechanical properties of 7175 aluminum were evaluated by means of SEM ?TEM ?mechanical properties and conductivity tests .
采用拉伸试验、电导率测试及电镜观察等方法,研究了重固溶制度后高温-低温-高温(HLH)再多级时效制度对7175铝合金组织与性能的影响。
2) solution
[英][sə'lu:ʃn] [美][sə'luʃən]
固溶
1.
Thermal analysis on runout table under on-line solution treatment;
在线固溶条件下的输出辊道受热分析
2.
Effect of solution temperature on aging of steel containing copper;
固溶温度对含铜钢时效行为的影响
3.
Phase Transformation Kinetics of Solutioned Cu-Ni-Si Alloy;
固溶态Cu-Ni-Si合金的相变动力学
3) solid solution
固溶
1.
Effect of Cold Rolling and Solid Solution Treatment on Structure and Mechanical Properties of Modified Type 202 Stainless Steel;
冷轧和固溶处理对改进型202不锈钢组织和力学性能的影响
2.
Effect of solid solution and aging on hardness of Cu-17Zn-0.4Cr alloy;
固溶时效对Cu-17Zn-0.4Cr合金硬度的影响
3.
Solid Solution and Aging Treatment of Thixoforming AZ91D Alloy
触变注射成形AZ91D的固溶和时效热处理
4) solid-solution
固溶
1.
Influence factors on solid-solution of carbonitride of niobium in steel
影响钢中铌的碳氮化物固溶的因素分析
2.
The microstructure and the mechanical performances of ZM5 magnesium alloys with RE-Ce addition in as-cast and solid-solution treatment state are investigated.
研究添加富铈混合稀土的ZM5合金在铸态和固溶处理后的显微组织与力学性能。
3.
The mechanical testing indicates that alloying and solid-solution treatment can evidently enhance mechanical properties of ZM5 alloy,Ca and mischmetal additions refined the microstructure obviously.
拉伸试验表明,合金元素的加入和固溶处理明显改善了ZM5镁合金的常温力学性能,微量Ca和稀土元素的加入能够显著细化显微组织。
5) solution treatment
固溶
1.
Effect of solution treatment with electric field on properties and fracture characters of Al-Li alloys;
电场固溶对铝锂合金性能和断裂特征的影响
2.
The microstructure and mechanical property of a new kind of cast duplex stainless steel after different solution treatment were studied by using optical microscope(OM),scanning electron microscope(SEM),X-ray diffraction and mechanical property testing.
采用金相显微镜(OM)、扫描电镜观察(SEM)、X射线衍射(X-Ray)分析及力学性能测试等研究手段,研究了不同固溶温度对某种新型铸造双相不锈钢组织及力学性能的影响。
3.
The effects of solution treatment and deformation-aging on the microstructures and tensile mechanical properties of Al-Cu-Li-Zr alloy were investigated by microstructure observations and tensile tests at room temperature.
通过显微组织观察和室温拉伸实验,研究了固溶热处理制度和时效前预变形对Al-Cu-Li-Sc-Zr合金拉伸力学性能和显微组织的影响。
6) Solid solution-exsolution
固溶-脱溶
补充资料：重固
1.稳固。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条