1) Ultra Low Carbon Enameling Steel
超低碳搪瓷钢
2) ultra-low-carbon enamelled steel
超低碳搪瓷钢板
1.
The effects of batch annealing(BA) and continuous annealing(CA) on mechanical properties and hydrogen storage property of ultra-low-carbon enamelled steels were investigated.
研究了两种不同退火工艺——罩式退火和连续退火工艺对含钛超低碳搪瓷钢板成型性能和贮氢性能的影响。
3) ULC steel
超低碳钢
1.
Study on the optimum process of refining ULC steel by RH degasser
RH冶炼超低碳钢的最优工艺研究
2.
Inclusions and total oxygen content in ultra-low carbon(ULC) steel were studied for the control of cluster inclusions in ULC steel.
为控制超低碳钢中的簇状夹杂物,对超低碳钢中的夹杂物和与全氧含量的关系进行了研究。
3.
The polarization curve of the ULC steel with titanium and niobium was measured to determine the suitable electrolytic parameters for preparation of TEM carbon replica samples.
测定了一种复合添加钛、铌超低碳钢的极化曲线,选用合适的电流密度和电解时间以碳复型方法萃取钢中的析出相制备透射电镜观察用样品。
4) ultra-low-carbon steel
超低碳钢
1.
Development on ultra-low-carbon steel mold powder of Baosteel;
宝钢超低碳钢保护渣的开发
2.
Effect of Mould Shielded Fluxes on Concasting Billet Surface Carbonization of Ultra-Low-Carbon Steel;
结晶器保护渣对超低碳钢连铸坯表面渗碳的影响
3.
Composite Treatment of Concasting Mold Flux for Ultra-Low-Carbon Steel;
超低碳钢连铸结晶器用保护渣的超细复合处理
5) Ultra Low Carbon Steel
超低碳钢
1.
Comparison of different flow stress models for ultra low carbon steels during warm deformation
超低碳钢低温变形流动应力模型的比较
2.
To address the characteristics of deformation behavior and flowing stress of ultra low carbon steel in the hot-strip mill processing,a set of simulations were performed with THERMECMASTOR-Z thermo dynamic simulator.
采用 THERMECMASTOR-Z 热/力模拟试验机研究了超低碳钢在铁素体区轧制过程的形变特征和流变应力,采用双段压缩试验方法研究了不同变形温度、道次间隔时间和变形程度对钢的流变应力和组织的影响。
3.
The reason and mathematic analysis for carbon pick up from mold flux have been investigated in ultra low carbon steel.
探讨了保护渣引起超低碳钢增碳的机理并进行了数学分析。
6) ultra-low carbon steel
超低碳钢
1.
Metallurgical effect test of tundish flux for ultra-low carbon steel;
超低碳钢中间包覆盖剂的冶金效果试验
2.
Influence of BN on ultra-low carbon steel continuous casting mold fluxes properties;
BN对超低碳钢连铸保护渣性能的影响
3.
Process optimization for production of ultra-low carbon steel by RH-MFB
RH-MFB生产超低碳钢的工艺优化
补充资料：搪瓷水箱
水箱具有现场组装灵活、不易变形、抗震性强、耐腐蚀、容易清洗及使用寿命长等优点。 二、适用范围 主要适用于建筑给水的调节、消防水箱、贮存水箱、采暖系统的膨胀、凝结水箱、建筑施工、道路施工、地质勘察以及国防工程等临时水箱。水箱既贮存冷水，也能贮存热水，耐酸、耐碱、不渗、不漏、不变形、不腐蚀。 三、选用说明 1．订货时应提供水箱尺寸、接管位置、管径大小。2．使用贮水温度4-65℃为宜。贮水温度高于此值时可于订货时提出，另行解决。3．水箱向地面荷重应由结构设计人员核定为准。4．用户提供的水箱接管位置恰在板缝处时，本公司需予以调整，管径不变(不另行通知用户)。搪瓷钢板水箱特点1、水质好。搪瓷瓷釉选用石英、长石、萤石等天然矿物质为原料，无毒无味、天然纯净。2、板材采用优质碳钢板，加工成标准板块3、钢板经过高温烤瓷，在1300℃高温下，离子之间相互渗透，结合成一体，永不脱落。4、现场组装，方便施工。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条