1) massive
[英]['mæsiv] [美]['mæsɪv]
块状
1.
Improve development response of fractured, bottom water, massive, metamorphic rock, and buried hill reservoir;
裂缝型底水块状变质岩古潜山油藏改善开发效果研究
2.
The partition characteristic of trace elements in the partial melting massive amphibolite at 1.5 GPa and 950 ℃
1.5GPa、950℃下块状斜长角闪岩部分熔融微量元素的分配特征
3.
It is single phase α microstructure of AZ80 alloy during compression at 400 ℃, however, there are massive β-Mg17Al12 phases precipitated in the alloy during water cooling after compression, it is fine and tight lamellar microstructure by high power observation.
结果表明,在200、250、300和350℃变形时,合金中的β-Mg17Al12相经直接变形破碎呈条状分布,变形温度越高,流线特征越明显;在400℃变形时,AZ80合金为单相α组织,但在变形后的水冷过程中,合金内部析出了块状的β-Mg17Al12相,经高倍观察为细小紧密的层片状组织。
2) lumpy
[英]['lʌmpi] [美]['lʌmpɪ]
成块的，块状
3) compacting and blocky
致密块状
1.
The hardness of compacting and blocky magnetite is high and the magnetite has big plasticity,so the magnetite is a kind of tough shooting ore.
致密块状磁铁矿坚硬,同时又具有较大的塑性,属于难爆矿石。
4) bulk amorphous alloy
块状非晶
1.
It is identified that a new bulk amorphous alloy with the largest supercooled liquid region TX of 100 K was obtaine.
用铜模铸造方法制备了不同尺寸的Zr55Al10Cu30Ni5-xPdx(x=0,1,3,5)块状非晶合金,采用X射线衍射(XRD)、扫描差热分析(DSC)和透射电镜(TEM)分别对Zr55A110Cu30Ni5-xPdx块状非晶样品的结构、热稳定性和微观组织进行了研究。
2.
The paper was based on preparing the bulk amorphous alloy and testing it's friction and wear property in Cu-Zr-Al system, the process of preparing the bulk amorphous alloy by magnetic levitation melting - copper modle suction method was studied ,what was more, prepared the metallic ,glass matrix composites by unidirectional solidification.
本文以Cu—Zr—Al系块状非晶的制备及其摩擦磨损性能研究为背景，对磁悬浮—铜模吸铸法制备块体非晶作了研究，并用定向凝固法制备了非晶基自生复合材料。
5) massive ore
块状矿石
1.
Re and Os concentrations and Os isotopic ratios for disseminated and massive ores from the Jinchuan Cu-Ni sulfide deposit are analyzed.
分析了金川铜镍硫化物矿床的一组浸染状矿石和一组块状矿石的Re、Os含量和Os同位素组成。
6) massive
[英]['mæsiv] [美]['mæsɪv]
巨厚块状
1.
Evaluation of watered-out and shutoff effect in massive extra-heavy oil reservoir;
巨厚块状特稠油油藏水淹特征及堵水效果评价
补充资料：高承载块状泡沫塑料
分子式：
CAS号：
性质：一种软质块状泡沫塑料。具有较高的压缩强度，减震性能优良。生产方法：(1)在普通软泡配方中添加无机填料；(2)在普通软泡配方中添加聚合物多元醇或聚脲分散体等有机填料；(3)以有机高官能度化合物作交联剂，提高软泡承载性。主要用于地毯底衬和精密仪器的包装材料等。
CAS号：
性质：一种软质块状泡沫塑料。具有较高的压缩强度，减震性能优良。生产方法：(1)在普通软泡配方中添加无机填料；(2)在普通软泡配方中添加聚合物多元醇或聚脲分散体等有机填料；(3)以有机高官能度化合物作交联剂，提高软泡承载性。主要用于地毯底衬和精密仪器的包装材料等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条