1) two extruding machines
两台挤出机
1.
Extrusion die design for compound triple-layer plastic pipe by two extruding machines is introduced.
介绍用两台挤出机共挤复合三层塑料管材机头的模具设计。
2) extruder output
挤出机挤出量
3) Extruder
[eks'tru:də]
挤出机
1.
Design of Novel Screw for Plastics Extruder—— Building Block Screw;
塑料挤出机新型螺杆——积木式螺杆的设计
2.
Regression models of influence factors in pin barrel extruder;
销钉机筒挤出机挤出质量影响因素的回归模型
3.
Servo Control and Temperature Regulate of Extruder;
挤出机的伺服控制与温度调节
4) Extrusion die
挤出机头
1.
Simulation of pressure distribution in L-shape sheet extrusion die by three-dimensional finite element method;
L形片材挤出机头流道压力分布三维有限元分析
2.
Development of ultra-wide rubber sheet extrusion die
超宽幅橡胶片材挤出机头的研制
3.
And the designs of blow mould and extrusion die are discussed accordingly.
以小型医用药瓶为例,分析了挤出吹塑成型工艺方案,选用一台挤出机同时挤出多个管坯的方法对药瓶进行挤出吹塑成型,并对吹塑模具和挤出机头的设计进行了探讨,找到了提高中小型中空塑件的挤出吹塑成型生产效率的途径。
5) Extruding machine
挤出机
1.
Design and Investigation of Temperature Control System for Hollow Blow Moulding Extruding Machine;
中空吹塑挤出机温控系统的设计与研究
2.
Selecting type and calculation of screw extruding machine in power coating;
粉末涂料用双螺杆挤出机的选型计算
6) extruder head
挤出机头
1.
A 3D FE model of double plex tread extruder head was established by selecting proper unit form properly dividing network units to obtain and analyze the pressure profile in head runner under a certain working conditions.
采用ANSYS有限元分析软件对胎面双复合挤出机头流道内部的压力场进行模拟和分析。
2.
Through analyses of the corrugated duct extruder heads of all kinds produced, as well as their developing situation, by some large companies abroad, a conclusion is drawn in the paper, that the extruder head of the elastic cock type and the one of spinning type are very much practical in use.
通过对国外一些大公司所研制的各种波纹管挤出机头的研制情况分析，得出了弹性螺塞结构型式的机头和旋转机头比较实用，同时在设计波纹管的机头时，主要以管机头和电缆挤出机头为基础，正确选择进料角和成型模具的尺寸，从而使机头结构更趋合理。
补充资料：两台
1.指唐武则天时肃政台(即御史台)的左右两台。左台知百司﹑监军旅，右台察州县﹑省风俗。见宋王应麟《小学绀珠．职官．两台》。 2.藩台和臬台的合称。指清代地方最高行政长官承宣布政使和提刑按察使。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条